1B9139 CUTTING EDGE Caterpillar parts
Rating:
Alternative (cross code) number:
CA1B9139
1B-9139
1B9139
CA1B9139
1B-9139
1B9139
Information:
Implement Tilt Lever
1. Tilt Forward Position - PUSH the lever FORWARD from HOLD position to tilt the implement forward. When the lever is released, it will return to HOLD position, and the implement will remain in the tilt forward position. 2. Tilt Hold Position - The implement will remain in the position it was in when the lever was released. 3. Tilt Back Position - PULL the lever BACK from HOLD position to tilt the implement back. After unloading, dumping, etc., the lever can be placed in the TILT BACK detent to return the implement to the preset angle. The tilt lever will return to HOLD when the preset angle is reached. The preset angle can be adjusted with the implement positioner linkage. The tilt back detent only functions after unloading, dumping, etc. The tilt back detent is used to return the implement to the preset implement angle. When the preset implement angle is reached, the tilt control lever should return to HOLD.Implement Lift Lever
1. Float Position - When the lever is pushed all the way forward into detent, the implement will be in FLOAT. In this position, the implement will lower to the ground and float, following ground variations.The lever will remain in float position (detent) until manually released by pulling it out of detent. The lever will then return to HOLD position.
Do not move the lever to FLOAT position with the implement loaded and raised.
2. Lower Position - PUSH the lever FORWARD from HOLD position to lower the implement. When the lever is released, the lever will return to HOLD position. 3. Hold Position - The implement will remain in the position it was in when the lever was released. 4. Raise Position - PULL the lever back from HOLD position to raise the implement. Release the lever to stop raising the implement. Lever will return to HOLD position. The lever is detented at the full RAISE position and will stay in detent until the implement reaches a predetermined height set by lift kickout linkage. The lever returns to HOLD when the implement reaches the predetermined height.Hydraulic Control Group Lever Lock
Released Position 1. - PULL the knob towards the operator to retract the lock rod and release the hydraulic control levers. Locked Position 2. - PUSH the knob away from the operator to extend the lock rod and lock the hydraulic control levers.Implement Function Control (Third Valve Function Only)
Pull lever back to pressurize the left supply line and control the implement rotation in one direction.Push lever forward to pressurize the right supply line and control the implement rotation in other direction. See the "Operating Techniques" section in this publication for more detailed instructions.Implement Coupler (Third Valve Function Only)
1. Disengage - Push the lever forward to disengage the coupler
1. Tilt Forward Position - PUSH the lever FORWARD from HOLD position to tilt the implement forward. When the lever is released, it will return to HOLD position, and the implement will remain in the tilt forward position. 2. Tilt Hold Position - The implement will remain in the position it was in when the lever was released. 3. Tilt Back Position - PULL the lever BACK from HOLD position to tilt the implement back. After unloading, dumping, etc., the lever can be placed in the TILT BACK detent to return the implement to the preset angle. The tilt lever will return to HOLD when the preset angle is reached. The preset angle can be adjusted with the implement positioner linkage. The tilt back detent only functions after unloading, dumping, etc. The tilt back detent is used to return the implement to the preset implement angle. When the preset implement angle is reached, the tilt control lever should return to HOLD.Implement Lift Lever
1. Float Position - When the lever is pushed all the way forward into detent, the implement will be in FLOAT. In this position, the implement will lower to the ground and float, following ground variations.The lever will remain in float position (detent) until manually released by pulling it out of detent. The lever will then return to HOLD position.
Do not move the lever to FLOAT position with the implement loaded and raised.
2. Lower Position - PUSH the lever FORWARD from HOLD position to lower the implement. When the lever is released, the lever will return to HOLD position. 3. Hold Position - The implement will remain in the position it was in when the lever was released. 4. Raise Position - PULL the lever back from HOLD position to raise the implement. Release the lever to stop raising the implement. Lever will return to HOLD position. The lever is detented at the full RAISE position and will stay in detent until the implement reaches a predetermined height set by lift kickout linkage. The lever returns to HOLD when the implement reaches the predetermined height.Hydraulic Control Group Lever Lock
Released Position 1. - PULL the knob towards the operator to retract the lock rod and release the hydraulic control levers. Locked Position 2. - PUSH the knob away from the operator to extend the lock rod and lock the hydraulic control levers.Implement Function Control (Third Valve Function Only)
Pull lever back to pressurize the left supply line and control the implement rotation in one direction.Push lever forward to pressurize the right supply line and control the implement rotation in other direction. See the "Operating Techniques" section in this publication for more detailed instructions.Implement Coupler (Third Valve Function Only)
1. Disengage - Push the lever forward to disengage the coupler
Parts cutting Caterpillar catalog:
1B9138
CUTTING EDGE
Caterpillar
Caterpillar
1B9137
CUTTING EDGE
Caterpillar
Caterpillar
1B9089
CUTTING EDGE
Caterpillar
Caterpillar
1B9087
CUTTING EDGE
Caterpillar
Caterpillar
1B9086
CUTTING EDGE
Caterpillar
Caterpillar
1B9085
CUTTING EDGE
Caterpillar
Caterpillar
1D0573
CUTTING EDGE
Caterpillar
Caterpillar
1D0572
CUTTING EDGE
Caterpillar
Caterpillar
1D0571
CUTTING EDGE
Caterpillar
Caterpillar
1D0570
CUTTING EDGE
Caterpillar
Caterpillar
1D0569
CUTTING EDGE
Caterpillar
Caterpillar
1D0568
CUTTING-EDGE
Caterpillar
Caterpillar