5D9559 CUTTING EDGE Caterpillar parts
120, 120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 143H, 14E, 16, 160G
Rating:
Alternative (cross code) number:
CA5D9559
5D-9559
5D9559
CA5D9559
5D-9559
5D9559
Weight: 130 pounds 58 kg.
Information:
BEVEL ANGLE
33
BOLT HOLE SIZE
18
mm
HOLE SPACING
152.4
mm
LENGTH
2131.2
mm
NUMBER OF HOLES
15
THICKNESS
19
mm
WIDTH
203.2
mm
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Grader Blade fits Caterpillar 5D-9559
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Grader Blade fits Caterpillar 5D-9559
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Compatible equipment models: 5D9559:
Information:
Alternator Bracket for Hydraulic Excavator
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) - 1/2 Inch Drive T50 Torx Bit 1
- 1/2 Inch Drive x 8 mm Hex Drive 1
B - Guide Studs
M10 by 80 mm 2
C - Guide Studs
M10 by 130 mm 2
(1) Either tool may be necessary in order to install the alternator pulley.
If necessary, follow Step 1.a through Step 1.k in order to install the alternator bracket to the cylinder block of the hydraulic excavator.
Ensure that all of the components of the alternator bracket are clean and free from wear and damage. Replace all components that are worn or damaged.
Illustration 1 g02095234
Position bracket (22) onto the cylinder block. Ensure that the bracket is correctly oriented.
Install bolts (23) and tighten the bolts to a torque of 44 N m (32 lb ft).
Illustration 2 g02165614
Illustration 3 g02352949
Install Tooling (B) to the cylinder block.
Position alternator bracket (17) onto Tooling (B). Install bolts (18) to the alternator bracket and hand tighten the bolts. Note: Support the alternator bracket as the bolts are installed. The weight of the bracket is approximately 19 kg (42 lb).
Remove Tooling (B) and install the remaining bolts (18) to the alternator bracket and hand tighten the bolts.
Ensure that spacers (20) are correctly installed to alternator bracket (17).
Install bolts (19) to alternator bracket (17) and hand tighten the bolts.
Illustration 4 g02165494
Tighten bolts (18) to a torque of 44 N m (32 lb ft).
Tighten bolts (19) to a torque of 44 N m (32 lb ft). Note: Ensure that Position (X) on alternator bracket (17) does not move in either direction.
Install the refrigerant compressor. Refer to Disassembly and Assembly, "Refrigerant Compressor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 5 g02022404
Illustration 6 g02165615
Illustration 7 g02352950
If necessary, follow Step 1.a through Step 1.h in order to install alternator bracket (11) onto the cylinder block.
Ensure that alternator bracket (11) is clean and free from wear and damage. If necessary, replace the alternator bracket.
Ensure that dowels (16) are free from wear and damage. If necessary, replace the dowels.
Install Tooling (B) to the cylinder block.
Position alternator bracket (11) onto Tooling (B). Install bolts (12) hand tight.
Remove Tooling (B) and install remaining bolts (12) hand tight.
Tighten bolts (12) to a torque of 44 N m (32 lb ft).
If necessary, install belt tensioner (14) onto alternator bracket (11) and tighten bolt (15). Refer to Disassembly and Assembly, "Belt Tensioner - Install" for the correct procedure.
If necessary, install flat idler pulley (13) onto alternator bracket (11). Refer to Disassembly and Assembly, "Idler Pulley (Flat Idler Pulley) - Remove and Install" for the correct procedure.
Illustration 8 g02019754
Typical example
If necessary, follow Step 2.a through Step 2.d in order to install pulley (8) to alternator (2). Note: Either of Tooling (A) may be required in order to carry out the installation of the alternator pulley.
Place alternator (2) in a suitable support.
Ensure that pulley (8) is correctly oriented.
Install pulley (8) and a new nut (9) to alternator shaft (10).
Position a
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) - 1/2 Inch Drive T50 Torx Bit 1
- 1/2 Inch Drive x 8 mm Hex Drive 1
B - Guide Studs
M10 by 80 mm 2
C - Guide Studs
M10 by 130 mm 2
(1) Either tool may be necessary in order to install the alternator pulley.
If necessary, follow Step 1.a through Step 1.k in order to install the alternator bracket to the cylinder block of the hydraulic excavator.
Ensure that all of the components of the alternator bracket are clean and free from wear and damage. Replace all components that are worn or damaged.
Illustration 1 g02095234
Position bracket (22) onto the cylinder block. Ensure that the bracket is correctly oriented.
Install bolts (23) and tighten the bolts to a torque of 44 N m (32 lb ft).
Illustration 2 g02165614
Illustration 3 g02352949
Install Tooling (B) to the cylinder block.
Position alternator bracket (17) onto Tooling (B). Install bolts (18) to the alternator bracket and hand tighten the bolts. Note: Support the alternator bracket as the bolts are installed. The weight of the bracket is approximately 19 kg (42 lb).
Remove Tooling (B) and install the remaining bolts (18) to the alternator bracket and hand tighten the bolts.
Ensure that spacers (20) are correctly installed to alternator bracket (17).
Install bolts (19) to alternator bracket (17) and hand tighten the bolts.
Illustration 4 g02165494
Tighten bolts (18) to a torque of 44 N m (32 lb ft).
Tighten bolts (19) to a torque of 44 N m (32 lb ft). Note: Ensure that Position (X) on alternator bracket (17) does not move in either direction.
Install the refrigerant compressor. Refer to Disassembly and Assembly, "Refrigerant Compressor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 5 g02022404
Illustration 6 g02165615
Illustration 7 g02352950
If necessary, follow Step 1.a through Step 1.h in order to install alternator bracket (11) onto the cylinder block.
Ensure that alternator bracket (11) is clean and free from wear and damage. If necessary, replace the alternator bracket.
Ensure that dowels (16) are free from wear and damage. If necessary, replace the dowels.
Install Tooling (B) to the cylinder block.
Position alternator bracket (11) onto Tooling (B). Install bolts (12) hand tight.
Remove Tooling (B) and install remaining bolts (12) hand tight.
Tighten bolts (12) to a torque of 44 N m (32 lb ft).
If necessary, install belt tensioner (14) onto alternator bracket (11) and tighten bolt (15). Refer to Disassembly and Assembly, "Belt Tensioner - Install" for the correct procedure.
If necessary, install flat idler pulley (13) onto alternator bracket (11). Refer to Disassembly and Assembly, "Idler Pulley (Flat Idler Pulley) - Remove and Install" for the correct procedure.
Illustration 8 g02019754
Typical example
If necessary, follow Step 2.a through Step 2.d in order to install pulley (8) to alternator (2). Note: Either of Tooling (A) may be required in order to carry out the installation of the alternator pulley.
Place alternator (2) in a suitable support.
Ensure that pulley (8) is correctly oriented.
Install pulley (8) and a new nut (9) to alternator shaft (10).
Position a
Cat SIS web machinery list:
Parts cutting Caterpillar catalog:
5D9558
CUTTING EDGE
120, 120B, 120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 163H
120, 120B, 120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 163H
4T2244
CUTTING EDGE CURVED 1.83 M (6 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
4T2231
CUTTING EDGE CURVED 1.83 M (6 FT.)
120G, 12G, 130G, 140G, 16H NA
120G, 12G, 130G, 140G, 16H NA
4T2242
CUTTING EDGE CURVED 2.13 M (7 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
5D9556
CUTTING EDGE - 6 FOOT
12F, 14E
12F, 14E
5D9557
CUTTING EDGE-7 FOOT
12F, 14E
12F, 14E
1D5728
CUTTING EDGE
120G, 12E, 14E
120G, 12E, 14E
5J6968
CUTTING EDGE
12E, 12F, 14E
12E, 12F, 14E
6G3828
CUTTING EDGE
140B
140B
4T2241
CUTTING EDGE STRAIGHT 2.13 M (7 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
4T2232
CUTTING EDGE STRAIGHT 1.83 M (6 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
4T2231
CUTTING EDGE CURVED 1.83 M (6 FT.)
120G, 12G, 130G, 140G, 16H NA
120G, 12G, 130G, 140G, 16H NA
4T2244
CUTTING EDGE CURVED 1.83 M (6 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
4T2243
CUTTING EDGE STRAIGHT 1.83 M (6 FT.)
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
5D9558
CUTTING EDGE
120, 120B, 120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 163H
120, 120B, 120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 163H