9K1619 CUTTING EDGE Caterpillar parts
980, 980B, 988
Rating:
Alternative (cross code) number:
CA9K1619
9K-1619
9K1619
CA9K1619
9K-1619
9K1619
Weight: 690 pounds 312 kg.
Information:
BEVEL ANGLE
22.5
BLUNT HEIGHT
15.7
mm
BOLT HOLE SIZE
1
mm
LENGTH
3270.25
mm
NUMBER OF HOLES
24
OVERALL WIDTH
304.8
mm
THICKNESS
44.45
mm
WHEEL LOADER,
Number on catalog scheme:
9
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9759 Jack Stand Gp 2
Illustration 1 g00949972
Use a suitable lifting device to position drum (6) in yoke (8). The weight of the drum is approximately 4875 kg (10750 lb).
Install any shims that were removed in the original locations. Install bolts (16) on both sides of drum (6) .
Use the suitable lifting device to raise drum (6) and remove Tooling (A). Lower the drum to the floor.
Illustration 2 g00949971
Position the hose assemblies for the drum propel motor between yoke (8) and drum (6). Install cover (14) .
Install clamps (15) and the bolts.
Illustration 3 g01013621
Connect hose assemblies (11) to drum propel motor (12) .
Install hose assemblies (13) on drum propel motor (12) .
Connect hose assembly (10) to final drive planetary (9) .
Illustration 4 g00949969
Position the hose assemblies for the vibratory motor between yoke (8) and drum (6). Install cover (7) .
Illustration 5 g01013619
Install hose assemblies (3) on vibratory motor (4) .
Connect hose assembly (5) to vibratory motor (4) .Note: Step 12 is required if the machine is equipped with a vibratory tachometer.
Connect the two wires to the sensor. Install clamp (2) and the bolts. Install the bolts that fasten bracket (1) to the plate. End By:
Install the front bumper. Refer to Disassembly and Assembly, "Front Bumper - Remove and Install".
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9759 Jack Stand Gp 2
Illustration 1 g00949972
Use a suitable lifting device to position drum (6) in yoke (8). The weight of the drum is approximately 4875 kg (10750 lb).
Install any shims that were removed in the original locations. Install bolts (16) on both sides of drum (6) .
Use the suitable lifting device to raise drum (6) and remove Tooling (A). Lower the drum to the floor.
Illustration 2 g00949971
Position the hose assemblies for the drum propel motor between yoke (8) and drum (6). Install cover (14) .
Install clamps (15) and the bolts.
Illustration 3 g01013621
Connect hose assemblies (11) to drum propel motor (12) .
Install hose assemblies (13) on drum propel motor (12) .
Connect hose assembly (10) to final drive planetary (9) .
Illustration 4 g00949969
Position the hose assemblies for the vibratory motor between yoke (8) and drum (6). Install cover (7) .
Illustration 5 g01013619
Install hose assemblies (3) on vibratory motor (4) .
Connect hose assembly (5) to vibratory motor (4) .Note: Step 12 is required if the machine is equipped with a vibratory tachometer.
Connect the two wires to the sensor. Install clamp (2) and the bolts. Install the bolts that fasten bracket (1) to the plate. End By:
Install the front bumper. Refer to Disassembly and Assembly, "Front Bumper - Remove and Install".
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar parts catalog:
Parts cutting Caterpillar catalog:
2V6119
CUTTING EDGE
980B
980B
8K9735
CUTTING EDGE
980, 980B
980, 980B
8J3962
CUTTING EDGE
992, 992C
992, 992C
6A4947
CUTTING EDGE
966C
966C
9K0356
CUTTING EDGE ASSEM.
980, 980B
980, 980B