1232044 CYLINDER GP Caterpillar parts
320B, 322B L, 322C FM, 325B L, 345B L, 5080
Rating:
Alternative (cross code) number:
CA1232044
123-2044
1232044
CA1232044
123-2044
1232044
Weight: 442 pounds 200 kg.
EXCAVATOR, FRONT SHOVEL,
Compatible equipment models: 1232044:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5593     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
Install the correct cylinder head gasket on the cylinder block.
Illustration 1 g01132970
Illustration 2 g00950659
Attach a suitable lifting device to cylinder head (10) . The weight of cylinder head (10) is approximately 227 kg (500 lb). Position cylinder head (10) on the engine block.
Lubricate the bolt threads, the underside of the bolt heads, and the washers on Bolt (1) through Bolt (26) with Tooling (A) prior to assembly.
Install bolts (9) . Refer to Step 6 for the correct tightening procedure.Note: Refer to Reuse and Salvage Guideline, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines" for reuse criteria of cylinder head bolts.
Tighten the cylinder head bolts according to the following procedure:
Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on Bolt (1) through Bolt (26) . Rotate Bolt (1) through Bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on Bolt (1) through Bolt (26) . Rotate Bolt (1) through Bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Tighten Bolt (27) through Bolt (34) in a numerical sequence to a torque of 55 10 N m (41 7 lb ft).
Install the cover for water regulator housing (14) .
Connect tube assembly (15) .
Connect hose assemblies (11) , (12) , (13) , and (16) .
Illustration 3 g01132968
Connect harness assembly (8) .
Install bolts (7) .
Illustration 4 g01132963
Install the bracket assembly and fuel filter base (4) .
Install oil level gauge tube (2) .
Connect harness assemblies (3) and (5) (not shown).
Connect hose assemblies (1) and (6) .
Fill the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".End By:
Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5593     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
Install the correct cylinder head gasket on the cylinder block.
Illustration 1 g01132970
Illustration 2 g00950659
Attach a suitable lifting device to cylinder head (10) . The weight of cylinder head (10) is approximately 227 kg (500 lb). Position cylinder head (10) on the engine block.
Lubricate the bolt threads, the underside of the bolt heads, and the washers on Bolt (1) through Bolt (26) with Tooling (A) prior to assembly.
Install bolts (9) . Refer to Step 6 for the correct tightening procedure.Note: Refer to Reuse and Salvage Guideline, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines" for reuse criteria of cylinder head bolts.
Tighten the cylinder head bolts according to the following procedure:
Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on Bolt (1) through Bolt (26) . Rotate Bolt (1) through Bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on Bolt (1) through Bolt (26) . Rotate Bolt (1) through Bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Tighten Bolt (27) through Bolt (34) in a numerical sequence to a torque of 55 10 N m (41 7 lb ft).
Install the cover for water regulator housing (14) .
Connect tube assembly (15) .
Connect hose assemblies (11) , (12) , (13) , and (16) .
Illustration 3 g01132968
Connect harness assembly (8) .
Install bolts (7) .
Illustration 4 g01132963
Install the bracket assembly and fuel filter base (4) .
Install oil level gauge tube (2) .
Connect harness assemblies (3) and (5) (not shown).
Connect hose assemblies (1) and (6) .
Fill the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".End By:
Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Caterpillar SIS machinery equipment:
Caterpillar SIS
5080 EXCAVATORS EQUIPPED WITH CUSTOM ATTACHMENTS 6XK00001-UP (MACHINE) »
123-2044
CYLINDER GP
325B L Excavator 2JR00001-UP (MACHINE) POWERED BY 3116 Engine »
123-2044
CYLINDER GP-BUCKET
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine »
123-2044
CYLINDER GP-BUCKET
322B L Excavator 1YS00001-UP (MACHINE) POWERED BY 3116 Engine »
123-2044
CYLINDER GP-BUCKET
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine »
123-2044
CYLINDER GP-BUCKET
345B, 345B L & 345B LC Excavator 2SW00001-UP (MACHINE) POWERED BY 3176C Engine »
123-2044
CYLINDER GP-BUCKET
320B, 320B L, 320B LN, 320B N & 320B S Excavators 1XS00001-UP (MACHINE) POWERED BY 3116 Engine »
123-2044
CYLINDER GP-BUCKET
322C FOREST SWING MACHINES BPH00001-UP (MACHINE) POWERED BY 3126 Engine »
123-2044
CYLINDER GP-BUCKET
322C Forest Swing Machines C3R00001-UP (MACHINE) POWERED BY 3126B Engine »
123-2044
CYLINDER GP-BUCKET
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
7Y1866
CYLINDER
1290T, 1390, 2491, 2590, 325D FM, 325D FM LL, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345B, 345B II, 345B II MH, 345B L, 345C...
1290T, 1390, 2491, 2590, 325D FM, 325D FM LL, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345B, 345B II, 345B II MH, 345B L, 345C...
1884211
CYLINDER AS
322B L, 322C, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D FM, 385B, 385C L, 568 FM LL, M325B
322B L, 322C, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D FM, 385B, 385C L, 568 FM LL, M325B
1028112
CYLINDER
1090, 1190, 1190T, 1390, 2290, 2390, 2391, 320 L, 320B, 320B FM LL, 322B L, 322C, 324D FM, 325, 325 L, 325B, 325B L, 511, 521, 522, OEMS, TK711, TK721, TK722, TK741
1090, 1190, 1190T, 1390, 2290, 2390, 2391, 320 L, 320B, 320B FM LL, 322B L, 322C, 324D FM, 325, 325 L, 325B, 325B L, 511, 521, 522, OEMS, TK711, TK721, TK722, TK741
1799765
CYLINDER AS
320B, 320C, 322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 345B II, 345B L
320B, 320C, 322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 345B II, 345B L
1163639
CYLINDER AS
322B L, 322C, 322C FM, 325B L, 330B, 330B L, 345B L, 350 L, M325B, W330B
322B L, 322C, 322C FM, 325B L, 330B, 330B L, 345B L, 350 L, M325B, W330B
2897798
CYLINDER AS
322B L, 322C FM, 324D FM, 324D FM LL, 325B L, 330B L, M325B, W330B
322B L, 322C FM, 324D FM, 324D FM LL, 325B L, 330B L, M325B, W330B
7I7712
CYLINDER
322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, OEMS
322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, OEMS
0874783
CYLINDER
320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 539, M325B
320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 539, M325B
1184001
CYLINDER AS
320B, 325B L
320B, 325B L
1793008
CYLINDER
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
1793044
CYLINDER
322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336...
322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336...
5I4311
CYLINDER
330, 330 FM L, 330 L, 330B, 330B L, 345B, 345B L, W330B
330, 330 FM L, 330 L, 330B, 330B L, 345B, 345B L, W330B
1179880
CYLINDER & SEAL GP
375, 5080
375, 5080
1880407
CYLINDER AR
365B
365B
1676750
CYLINDER GP
330B L, 345B II, 345B L
330B L, 345B II, 345B L
1676748
CYLINDER & SEAL GP
330B L, 345B II, 345B L
330B L, 345B II, 345B L
1891527
CYLINDER GP
325B L, 330B L
325B L, 330B L
1844122
CYLINDER GP
5080
5080
1782205
CYLINDER GP
5080
5080
1788449
CYLINDER GP
5080
5080