CYLINDER HEAD GP 1247372 - Caterpillar

1247372 CYLINDER HEAD GP Caterpillar parts G3412C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1247372
124-7372
1247372

Weight: 305 pounds 138 kg.

Buy CYLINDER HEAD GP 1247372 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Hex Socket Cap Screw Plain Stainless Steel M10x35mm 0.06in (1.5mm) Thread Pitch, Pack of 10, MFR: 1247372

$14.95

03 Apr 2025

US: ONYX PRIME

Hex Socket Cap Screw Plain Stainless Steel M10x35mm 0.06in (1.5mm) Thread Pitch, Pack of 10, MFR: 1247372
Generic Alternate Mfr Part Number: 1247372; Drive Type: Hex Socket; Finish: Plain; Head Type: Hex Socket Cap Head; Screw Material: A4 Stainless Steel; Screw Thread Size: M10; Series: 84020102 Series; Size: M10x35 mm; System of Measurement: Metric; Type: Hex Socket Cap || Metric Thread A4 Socket Hexagon Cap Head Screws || The hexagon head socket cap screws have a narrow head and are perfect for use in hard to reach areas. The fasteners are good in machine repair and maintenance applications also in many other sectors including food and beverage, automotive and aerospace. || This range of fasteners are produced from A4 (316) Stainless Steel making them ideal for use in the food and beverage, offshore and marine industry. A4 (316) stainless steel has greater corrosion resistance than A2 Stainless Steel but is more expensive, although more affordable than Titanium which provides even greater levels of corrosion resistance.

Number on catalog scheme: 1

Caterpillar 1247372 Parts scheme CYLINDER HEAD GP

For full view, you need register

Compatible equipment models: 1247372:

GEN SET ENGINE G3412C Caterpillar

Information:

Sudden movement of the machine or release of oil under pressure can cause serious injury to persons on or near the machine.To prevent possible injury, perform the procedure that follows before testing and adjusting the hydraulic system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Table 1
Required Tools
Tools Part Number Description Qty
A 4C-8689 Flow Meter 1
8C-6874 Connector 2
6V-8399 O-Ring Seal 2
6V-8942 O-Ring Reducer 2
6V-8556 Nut 2
6V-8398 O-Ring Seal 2
124-2160 Coupling 1
124-2114 Coupling 1
5P-3413 Pipe Sealant 1
122-6889 Hydraulic Hose 36 in
B 4C-6500 Digital Thermometer 1 Note: Perform the following steps before conducting this procedure.
Move the machine to a smooth, horizontal location that is away from operating machines and away from personnel.
Place the propel control lever in NEUTRAL.
Engage the parking brake.
Stop the engine.
Illustration 1 g01049545
Rear Vibratory Motor
(1) T1 port
(2) T2 port
Disconnect hose from T1 (1). Cap the port and plug the hose. Note: If the front motor is being tested, disconnect the hose from the T2 port. Cap the port and plug the hose.
Disconnect hose from T2 port (2), and install Tool A. Orient the flow meter in the direction of flow. The flow travels from the motor to the return manifold. Note: If the front motor is being tested, disconnect the hose from the T1 port, and install Tool A.
Start and operate the engine at HIGH IDLE at 2370 50 rpm. Monitor the hydraulic oil temperature with Tool B. Operate the machine until the oil temperature reaches 43° 5.6°C (110° 10°F).
Read the flow on Tool A. The flow should be less than 3.5 L/min (1.0 US gpm). Note: Motor case drain flow cannot be adjusted. If the case drain flow is greater than the specification, the motor may need to be repaired.
Stop the engine. Remove Tool A. Reconnect the hoses to T1 port (1) and T2 port (2). Repeat for the other vibratory motor.