1435988 CYLINDER GP-BLADE TIP Caterpillar parts
24H, 24M
Rating:
Alternative (cross code) number:
CA1435988
143-5988
1435988
CA1435988
143-5988
1435988
Weight: 105 pounds 47 kg.
Information:
BORE DIAMETER
120.65
mm
CLOSED LENGTH
655
mm
PIN SIZE CAP END
57.1
mm
PIN SIZE ROD EYE
57.1
mm
ROD DIAMETER
63.5
mm
STROKE
294
TYPE
THD GLAND
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Sufficient Warmup Time
Generators should be warmed up before returning to full operation. Damage to valves and components during operation in cold temperature conditions can result from generator operation for short intervals. Damage to the generator can occur from starting the generator and stopping the generator many times without allowing the generator to reach normal operating temperature. The fuel and the oil are not completely burned in the combustion chambers while the generator is operating below the normal operating temperature. This fuel and oil causes soft carbon deposits on the valve stems. Generally, these deposits do not cause problems because these deposits are burned off during operation at normal generator temperatures. When the generator is started and the generator is stopped frequently, the generator may not reach the normal operating temperature. When the normal operating temperature is frequently not reached, carbon deposits will become thicker. Buildup of carbon deposits will prevent the free operation of the valves. This can also cause the following conditions: valves to stick, pushrods to bend, and other damage to valve train components. Operate the generator at no load until the coolant temperature is at a minimum temperature of 71° C (160° F). This will keep the carbon deposits on the valve stems at a minimum. This will also maintain free operation of the valves and the valve train components. The generator will remain in better condition and the service life of the generator may be extended when the generator is warmed up at no load. Lubrication will be improved, with less acid and sludge in the oil. Reduction of acid and sludge in the oil will allow for longer service life of the generator bearings, the pistol rings, and other parts. Limit unnecessary idle time to 10 minutes. Generator wear is greatest at low idle and unnecessary idling wastes fuel.The optional starting aid switch is used to inject ether into the generator for starting in cold weather conditions. Refer to for further information.
Generators should be warmed up before returning to full operation. Damage to valves and components during operation in cold temperature conditions can result from generator operation for short intervals. Damage to the generator can occur from starting the generator and stopping the generator many times without allowing the generator to reach normal operating temperature. The fuel and the oil are not completely burned in the combustion chambers while the generator is operating below the normal operating temperature. This fuel and oil causes soft carbon deposits on the valve stems. Generally, these deposits do not cause problems because these deposits are burned off during operation at normal generator temperatures. When the generator is started and the generator is stopped frequently, the generator may not reach the normal operating temperature. When the normal operating temperature is frequently not reached, carbon deposits will become thicker. Buildup of carbon deposits will prevent the free operation of the valves. This can also cause the following conditions: valves to stick, pushrods to bend, and other damage to valve train components. Operate the generator at no load until the coolant temperature is at a minimum temperature of 71° C (160° F). This will keep the carbon deposits on the valve stems at a minimum. This will also maintain free operation of the valves and the valve train components. The generator will remain in better condition and the service life of the generator may be extended when the generator is warmed up at no load. Lubrication will be improved, with less acid and sludge in the oil. Reduction of acid and sludge in the oil will allow for longer service life of the generator bearings, the pistol rings, and other parts. Limit unnecessary idle time to 10 minutes. Generator wear is greatest at low idle and unnecessary idling wastes fuel.The optional starting aid switch is used to inject ether into the generator for starting in cold weather conditions. Refer to for further information.
Caterpillar SIS machinery equipment:
Caterpillar SIS
24 Motor Grader N9Z00001-UP (MACHINE) POWERED BY C27 Engine »
143-5988
CYLINDER GP-BLADE TIP
24 Motor Grader E9Z00001-UP (MACHINE) POWERED BY C27 Engine »
143-5988
CYLINDER GP-BLADE TIP
24H Motor Grader 7KK00001-UP (MACHINE) POWERED BY 3412E Engine »
143-5988
CYLINDER GP-BLADE TIP
24M Motor Grader B9K00001-UP (MACHINE) POWERED BY C18 Engine »
143-5988
CYLINDER GP-BLADE TIP
24M Motor Grader B9300001-UP (MACHINE) POWERED BY C18 Engine »
143-5988
CYLINDER GP-BLADE TIP
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
1430047
CYLINDER HEAD AS
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, 992D, C30, C32, D10N, D10R, D9L, PM3412, PR-1000, SCT673, SPS342, SPT342
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, 992D, C30, C32, D10N, D10R, D9L, PM3412, PR-1000, SCT673, SPS342, SPT342
1081887
CYLINDER HEAD GP
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, D10N, D10R, D9L
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, D10N, D10R, D9L
7W2243
CYLINDER HEAD AS
24H, 3412, 3412C, 3412E, 651E, 657E, 772B, 773B, 773D, 775B, 775D, 990, 990 II, 992C, 992D, D10N, D10R, D9L, PR-1000, PR-750B
24H, 3412, 3412C, 3412E, 651E, 657E, 772B, 773B, 773D, 775B, 775D, 990, 990 II, 992C, 992D, D10N, D10R, D9L, PR-1000, PR-750B
1921322
CYLINDER HEAD AS
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, C30, C32, D10N, D10R, D9L
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, C30, C32, D10N, D10R, D9L
2237263
CYLINDER HEAD AS
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 583T, 587T, 621G, 623G, 627F, 627G, 631D, 631G, 637G, 651B, 657B, 657E, 657G, 735, 740, 770, 772, 824C, 824G I...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 583T, 587T, 621G, 623G, 627F, 627G, 631D, 631G, 637G, 651B, 657B, 657E, 657G, 735, 740, 770, 772, 824C, 824G I...
2811640
CYLINDER HEAD AS
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
2239250
CYLINDER HEAD GP
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 583T, 587T, 621G, 623G, 627F, 627G, 631D, 631G, 637G, 651B, 657B, 657E, 657G, 735, 740, 770, 772, 824C, 824G I...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 583T, 587T, 621G, 623G, 627F, 627G, 631D, 631G, 637G, 651B, 657B, 657E, 657G, 735, 740, 770, 772, 824C, 824G I...
1137754
CYLINDER GP-RIPPER
120K, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 24M
120K, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 24M
2674631
CYLINDER BLOCK AS
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B, 657E, 657G, 73...
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B, 657E, 657G, 73...
2635055
CYLINDER HEAD GP
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
1170836
CYLINDER GP-WHEEL LEAN
24H, 24M
24H, 24M
2360737
CYLINDER
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
1408444
CYLINDER & MTG GP-BLADE TIP
24H, 24M
24H, 24M
1839024
CYLINDER & SEAL GP-BOOM
M322C, M322D, M322D MH
M322C, M322D, M322D MH
2963236
CYLINDER GP-HYDRAULIC
M318C, M318C MH, M318D, M318D MH
M318C, M318C MH, M318D, M318D MH
2111987
CYLINDER & MTG GP-TELESCOPING
TH220B, TH460B, TH560B
TH220B, TH460B, TH560B
2840813
CYLINDER GP-HYDRAULIC
RM-300, RM-500
RM-300, RM-500
3596693
CYLINDER GP-TILT
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
1753217
CYLINDER HEAD AS
3116, 3126
3116, 3126