1650102 CYLINDER GP-RIPPER TIP Caterpillar parts
D8R, D8R II, D8T
Rating:
Alternative (cross code) number:
CA1650102
165-0102
1650102
CA1650102
165-0102
1650102
Weight: 325 pounds 147 kg.
Information:
BORE DIAMETER
165.1
mm
CLOSED LENGTH
1162
mm
PIN SIZE CAP END
76.2
mm
PIN SIZE ROD EYE
76.2
mm
ROD DIAMETER
76.2
mm
STROKE
437
TYPE
BOLTED HEAD
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1650102 Hydraulic Cylinder for Model D8R/D8R II/D8T
CTP For Model D8R/D8R II/D8T || Sold in each || Easy in-and-out fit
CTP For Model D8R/D8R II/D8T || Sold in each || Easy in-and-out fit
CTP 1650102 Hydraulic Cylinder for Model D8R/D8R II/D8T
CTP For Model D8R/D8R II/D8T || Sold in each || Easy in-and-out fit
CTP For Model D8R/D8R II/D8T || Sold in each || Easy in-and-out fit
Information:
Many new Cat products are now using maintenance-free batteries. These batteries require different test procedures from conventional batteries. Since there are no vent plugs on maintenance-free batteries, there is no way to check the specific gravity of the electrolyte. A hydrometer cannot be used. Instead, the voltage of the battery must be checked to determine the state of charge.
Measure the open circuit voltage of the battery. Use a digital volt meter such as 6V7070 Multimeter Group. Set the meter on the 20 volt DC scale and touch the probes to the battery terminals. If the battery voltage is 12.40 or above, the battery is ready for use. If below 12.40 volts, it must be recharged for satisfactory performance.
If a maintenance-free battery is being considered for warranty, the same voltage check must be done before performing a load test. Maintenance-free batteries below 12.40 volts will fail a load test, but still may be good, serviceable batteries when recharged.
When maintenance-free batteries are deeply discharged, they may not recharge if you just jump-start the engine. Cat alternators produce 13.8 volts on 12 volt products and 27.5 volts on 24 volt products. But 16 volts (32 volts on 24 volt systems) may be required for charging to begin. Recharge with a battery charger capable of supplying 16 volts so that the batteries will accept a charge. Once they accept charging current, indicated by an increase in the charger ammeter reading, the voltage must then be reduced. It is important not to let the charging voltage exceed 16.0 volts, especially as the battery becomes fully charged.
The Cat maintenance-free battery used in original equipment (3T5760) is designed and built to rigid Cat specifications. It can be deeply discharged, such as by leaving the lights on over a weekend, and still be a good serviceable battery when fully recharged. For complete testing and charging information, refer to Special Instruction, Form SEHS7633, "Battery Test Procedure."
Measure the open circuit voltage of the battery. Use a digital volt meter such as 6V7070 Multimeter Group. Set the meter on the 20 volt DC scale and touch the probes to the battery terminals. If the battery voltage is 12.40 or above, the battery is ready for use. If below 12.40 volts, it must be recharged for satisfactory performance.
If a maintenance-free battery is being considered for warranty, the same voltage check must be done before performing a load test. Maintenance-free batteries below 12.40 volts will fail a load test, but still may be good, serviceable batteries when recharged.
When maintenance-free batteries are deeply discharged, they may not recharge if you just jump-start the engine. Cat alternators produce 13.8 volts on 12 volt products and 27.5 volts on 24 volt products. But 16 volts (32 volts on 24 volt systems) may be required for charging to begin. Recharge with a battery charger capable of supplying 16 volts so that the batteries will accept a charge. Once they accept charging current, indicated by an increase in the charger ammeter reading, the voltage must then be reduced. It is important not to let the charging voltage exceed 16.0 volts, especially as the battery becomes fully charged.
The Cat maintenance-free battery used in original equipment (3T5760) is designed and built to rigid Cat specifications. It can be deeply discharged, such as by leaving the lights on over a weekend, and still be a good serviceable battery when fully recharged. For complete testing and charging information, refer to Special Instruction, Form SEHS7633, "Battery Test Procedure."
Caterpillar SIS machinery equipment:
Caterpillar SIS
D8T TRACK-TYPE TRACTOR MB800001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR JJ500001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR DWJ00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR AW400001-UP (MACHINE) POWERED BY C15 ENGINE »
165-0102
CYLINDER GP-RIPPER TIP
D8R Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR 9EM00001-UP (MACHINE) POWERED BY 3406C Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R Series II Track-Type Tractor 6YZ00001-UP (MACHINE) POWERED BY 3406E Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR Differential Steering AKA00001-UP (MACHINE) POWERED BY 3406E Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR KPZ00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR J8B00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR MLN00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR FCT00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR RJM00001-UP (MACHINE) POWERED BY 3406C Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR T5X00001-UP (MACHINE) POWERED BY 3406C Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 Engine »
165-0102
CYLINDER GP-RIPPER TIP
D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C Engine »
165-0102
CYLINDER GP-RIPPER TIP
Cat SIS web machinery list:
Parts cylinder Caterpillar catalog:
2454324
CYLINDER HEAD AS
3406E, 3456, 385B, 621G, 623G, 627G, 735, 740, 824G, 824G II, 825G II, 826G II, 834G, 836G, 980G, 980G II, 988G, C-15, C-16, C-18, C16, C18, D350E II, D400E II, D8R II
3406E, 3456, 385B, 621G, 623G, 627G, 735, 740, 824G, 824G II, 825G II, 826G II, 834G, 836G, 980G, 980G II, 988G, C-15, C-16, C-18, C16, C18, D350E II, D400E II, D8R II
6E1175
CYLINDER GP-TILT
D8N, D8R, D8R II
D8N, D8R, D8R II
2505861
CYLINDER GP-BULLDOZER LIFT
D8R, D8T
D8R, D8T
9T0143
CYLINDER GP-RIPPER TILT
D8N, D8R
D8N, D8R
1769918
CYLINDER HEAD GP
3406E, 3456, 385B, 5090B, 980G II, AD30, AD55, C-15, D8R II, MTC835, R2900, R2900G
3406E, 3456, 385B, 5090B, 980G II, AD30, AD55, C-15, D8R II, MTC835, R2900, R2900G
2141667
CYLINDER HEAD GP
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
6E1102
CYLINDER GP-BULLDOZER LIFT
D8N, D8R, D8R II
D8N, D8R, D8R II
2407347
CYLINDER GP-TILT
D8R, D8T
D8R, D8T
6E3976
CYLINDER AS
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
7T3697
CYLINDER AS
D8N, D8R
D8N, D8R
6E1176
CYLINDER AS
D8N, D8R, D8R II
D8N, D8R, D8R II
6E1103
CYLINDER AS
D8N, D8R, D8R II
D8N, D8R, D8R II
1627858
CYLINDER HEAD GP
3054, AP-800C, BG-225B, BG-225C, CB-534C, CP-433C, CS-431C, M315, PF-290B, PS-200B, PS-360B, TH103, TH62, TH63, TH82, TH83
3054, AP-800C, BG-225B, BG-225C, CB-534C, CP-433C, CS-431C, M315, PF-290B, PS-200B, PS-360B, TH103, TH62, TH63, TH82, TH83
3504423
CYLINDER HEAD GP
824G, 825G, 826C, 826G, 980G
824G, 825G, 826C, 826G, 980G
3672084
CYLINDER BLOCK GP
3054C, C4.4
3054C, C4.4
2370842
CYLINDER BLOCK GP
773F, 775F, 844H, 990H, AD55B, C27, D10N, D10R, D10T, TH48-E70
773F, 775F, 844H, 990H, AD55B, C27, D10N, D10R, D10T, TH48-E70
7N0841
CYLINDER BLOCK AS
3412, 651E, 657E, 772B, 773B, 775B, 990, 992C, 992D, D10N, D9L, G3412, PR-1000, PR-750B
3412, 651E, 657E, 772B, 773B, 775B, 990, 992C, 992D, D10N, D9L, G3412, PR-1000, PR-750B
9N1105
CYLINDER HEAD GP
225, 227, 229, 3208, 613B, CB-614, CS-551, PS-500
225, 227, 229, 3208, 613B, CB-614, CS-551, PS-500
1248308
CYLINDER & MTG GP-ELEVATION
PM-565, PM-565B
PM-565, PM-565B
2639577
CYLINDER BLOCK GP
C13, TH35-C13T
C13, TH35-C13T
2043696
CYLINDER & SEAL GP-BUCKET
320C, 322C, 325C L
320C, 322C, 325C L