AVSPARE.COM
parts catalog

CYLINDER & SEAL GP-BUCKET 1915553 - Caterpillar


1915553 CYLINDER & SEAL GP-BUCKET Caterpillar parts 330C, 330C L
Rating:
40
Alternative (cross code) number:
CA1915553
191-5553
1915553
Caterpillar 1915553 CYLINDER & SEAL GP-BUCKET

Buy CYLINDER & SEAL GP-BUCKET 1915553 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1915553:

EXCAVATOR  330C   330C L   Caterpillar
  For full view, you need register

Information:


Illustration 2 g00615790
Retaining Bar (2) Retaining bar
If the generator end housing is equipped with retaining bars (2), remove the four bolts that fasten the retaining bars to the generator end housing. Remove the retaining bars.
Illustration 3 g00615797
Bearing Cap (3) Bearing Cap
If the generator end housing is equipped with bearing cap (3), remove the necessary bolts which fasten the bearing cap to the generator end housing. Pry the bearing cap out of the generator end housing. The bearing cap remains with the rotor shaft. If a bearing lube line is attached to the bearing cap, remove the lube line.
Illustration 4 g00615803
(4) End housing (5) BoltsNote: The weight of end housing (4) varies with the size of the generator. Larger end housings require the use of a hoist.
Attach a hoist to end housing (4). Remove bolts (5) that fasten end housing (4) to the generator. Use a pry bar to separate the end housing from the generator. Some end housings have provisions which allow the use of forcing screws. Lift the end housing from the generator and remove the end housing from the generator.
Illustration 5 g00615809
(6) Tooling
Attach tooling (6). Remove the bearing. Two-Bearing Generator
Table 2
TOOLS NEEDED    
Part Number     Tool     Quantity    
1U-6415     Puller Group (40 ton)     1    Note: On two-bearing generators, there is a bearing on each end of the generator. To remove the bearing that is located at the drive end of the generator, use the following procedure.For removal of the bearing at the drive end of the generator, begin by removing the drive coupling. Refer to Disassembly and Assembly, "Coupling - Remove".
Illustration 6 g00615814
(1) Bolts
The generator bearing is retained in the generator end housing. On the inside of the generator end housing, a bearing cap retains the bearing. Remove bolts (1) which fasten the bearing cap to the generator end housing. Pry the bearing cap out of the generator end housing. The bearing cap remains with the rotor shaft. If a bearing lube line is attached to the bearing cap, remove the lube line.
Illustration 7 g00615816
(2) End Housing (3) Bolts
Attach a hoist to end housing (2). Remove bolts (3) which fasten end housing (2) to the generator. Use a pry bar to separate the end housing from the generator. Some end housings have provisions which allow the use of forcing screws. Lift the end housing from the generator and remove the end housing from the generator.
Illustration 8 g00615820
(4) Removal Tool 1U-6415
Attach tooling (4). Remove the bearing.
Illustration 9 g00615824
Replaceable bearing wear sleeve (inside view of end housing) (5) Bearing wear sleeveSome end housings have a bearing wear sleeve (5) which is replaceable. Installation Procedure
To install the bearing that is located at the exciter end of the generator, use the following procedure.
Heat the bearing to 107 °C (224.6 °F).
While the bearing is heated to 107 °C (224.6°F), place the bearing inside the end housing.
If the generator end housing is equipped with a bearing cap, attach bearing cap to the end housing. Install bolts.
If equipped, attach bearing lube line to the

Caterpillar parts catalog:

Caterpillar parts catalog
330C L & 330C LN Excavators CAP00001-UP (MACHINE) POWERED BY C-9 Engine
330C & 330C L Excavators GKX00001-UP (MACHINE) POWERED BY C-9 Engine
330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine
330C L Excavator DKY00001-UP (MACHINE) POWERED BY C-9 Engine
330C L Excavator CYA00001-UP (MACHINE) POWERED BY C-9 Engine
330C L Material Handler MKM00001-UP (MACHINE) POWERED BY C-9 Engine
330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine


Parts cylinder Caterpillar catalog:

2105987 CYLINDER HEAD GP
12H, 330C, 330C FM, 330C L, 330C MH, 627G, 637D, 637G, 973C, C-9, D6R II, MTC735, TK711, TK721, TK722, TK732, TK741, TK751, TK752
3253915 CYLINDER BLOCK AS
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521...
2733034 CYLINDER HEAD GP
12H, 330C, 330C FM, 330C L, 330C MH, 627G, 637D, 637G, C-9, D6R II, MTC735, TK711, TK721, TK722, TK732, TK741, TK751, TK752
2478853 CYLINDER GP-BUCKET
322C, 325C, 330C, 330C L, 385B, 385C L
1884211 CYLINDER AS
322B L, 322C, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D FM, 385B, 385C L, 568 FM LL, M325B
1771765 CYLINDER & SEAL GP-BOOM
325B L, 325C FM, 325D FM, 325D FM LL, M325B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.