1U3374 CYLINDER AS Caterpillar parts
10, D10
Rating:
Alternative (cross code) number:
CA1U3374
1U-3374
1U3374
CA1U3374
1U-3374
1U3374
Weight: 20 pounds 9 kg.
Information:
BORE DIAMETER
101.6
mm
GREASE PORT
N
MOUNT TYPE
YOKE
TYPE
1
RIPPER, TRACK-TYPE TRACTOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01434456
Use two people in order to install axle oil cooler (6). The weight of axle oil cooler (6) is approximately 27 kg (60 lb). Position axle oil cooler (6) and install bolts (5).
Connect hose assemblies (7).
Illustration 2 g01434450
Install plate assembly (4).
Illustration 3 g01434446
Install plate assemblies (3). Install panel assembly (2).
Illustration 4 g01433075
Close grill assembly (1). Repeat for the opposite side.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01434456
Use two people in order to install axle oil cooler (6). The weight of axle oil cooler (6) is approximately 27 kg (60 lb). Position axle oil cooler (6) and install bolts (5).
Connect hose assemblies (7).
Illustration 2 g01434450
Install plate assembly (4).
Illustration 3 g01434446
Install plate assemblies (3). Install panel assembly (2).
Illustration 4 g01433075
Close grill assembly (1). Repeat for the opposite side.
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
1U3373
CYLINDER GP
10, D10, D8L, D9L
10, D10, D8L, D9L
3G2222
CYLINDER GP-RIPPER LIFT
10, D10, D11N
10, D10, D11N
3G2220
CYLINDER GP-RIPPER TILT
10, D10
10, D10
8J2071
CYLINDER GP
10, 8D, D9H
10, 8D, D9H
3G2221
CYLINDER GP-RIPPER LIFT
10, D10, D11N
10, D10, D11N
776, 777, 992, D10, D348
8J2072
CYLINDER ASSEM.
10, 8D
10, 8D
3G2219
CYLINDER ASSEM.
10, D10
10, D10
7A, D7G
3G6828
CYLINDER AS-HYD
D8L, D9N
D8L, D9N
9P6840
CYLINDER ASSEM. (L.H.)
D8L, D9N
D8L, D9N
9P6841
CYLINDER ASSEM. (R.H.)
D8L, D9N
D8L, D9N