CYLINDER AS 2167387 - Caterpillar

All 6 hoses are not needed for anyone engine. Only order the hose and elbow combination required for theengine being repaired.ACTION REQUIRED
See the attached Rework Procedure.OWNER NOTIFICATION
U.S. and Canadian owners will receive the attachedOwner Notification.SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts Labor Hrs. Parts Labor Hrs. Parts Labor Hrs.
100% 2.5 0 0 0 0
This is a 2.5-hour job. An additional0.4 hours may be claimed for each line replaced
SMCS Description SC MC CV CO
7751-036-SLI Field Update Program 2.5 2.5 2.5 2.5
7755-010-LI * Turbo Line R&I 0.4 0.4 0.4 0.4* Use this code for each supply line repaired.PARTS DISPOSITION
***** U.S. and Canadian Dealers ***** Make sure the outside of the shippingcontainer is marked PI30698.Return all supply hoses that are replaced anda copy of the claim to:Caterpillar Inc.Attn: PI30698
Service Claims Room
8201 N. University
Peoria, IL 61615***** All Other Dealers *****Handle the parts in accordance with your WarrantyBulletin on warranty parts handling.MAKE EVERY EFFORT TO COMPLETE THIS PROGRAMAS SOON AS POSSIBLE.Attach. (1-Owner Notification)
(2-Rework Procedure)COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS
XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999PRIORITY - The Turbo Oil Supply Lines NeedTo Be InspectedMODELS INVOLVED - C15 EnginesDear Caterpillar Product Owner:The turbo oil supply lines need to be inspectedon certain C15 On-Highway Truck Engines. The turbo oil supply lines oncertain C15 Engines may leak. The turbo supply lines need to be inspectedand, if needed, repairs made on the products listed below. You will notbe charged for the service performed.Contact your local Caterpillar dealer immediatelyto schedule this service. The dealer will advise you of the time requiredto complete this service. Please refer the dealer to their Service Letterdated August 10, 2004 when scheduling this service.We regret the inconvenience this may causeyou, but urge you to have this service performed as soon as possible toprevent unscheduled downtime.Caterpillar Inc.
Identification #(s)Attached to August 10, 2004 Service LetterRework Procedure
Verify that the most current software is installed.If it is not, flash engine with the latest software.
Run at 1600 RPM for 5 minutes.
Shut-off the engine and allow it to cool.
Perform a visual inspection of the turbo oil supplyhose on the high-pressure turbo. Pay particular attention to the threeareas on each hose identified in Illustration 1.
If no oil leak is visible, continue with procedure.
If oil leak is visible, replace the hose and elbowfitting and return to step 1. Use table 1 to determine which hose to order.
Illustration 1
Unbolt turbo oil supply flange from the turbo.
Pull on turbo oil supply line with 20 to 50 poundsto ensure proper connection at lower fitting.
Note: While pulling on hose, brace yourselfand pull straight out from lower fitting
If hose is not connected, push hose untilconnection is achieved and repeat pull test.
If hose is connected, continue with inspectionprocedure.
Re-install the flange to turbo using a new 1978418Gasket.
Repeat inspection procedure for other turbo oilsupply hose.
Run engine at 1600 RPM for 5 minutes.
Shut-off engine and allow engine to cool.
Perform visual inspection of both turbo oil supplyhoses.
When the procedure is complete, stamp the letters"TS" to the right of the engine serial number plate on the cylinder blockto signify that this rework has been completed.