CYLINDER BLOCK GP 2202668 - Caterpillar

2202668 CYLINDER BLOCK GP Caterpillar parts 416D, 420D, 428D, 430D, 432D, 438D, 442D

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$15.23

10 May 2024

Amazon.com

Sunsong 2202668 Brake Hydraulic Hose
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing

$15.23

03 Feb 2024

Amazon.com

Sunsong 2202668 Brake Hydraulic Hose
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing

$18.76

04 Sep 2023

Amazon.com

Sunsong 2202668 Brake Hydraulic Hose
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing

Compatible equipment models: 2202668:

BACKHOE LOADER 416D 420D 428D 430D 432D 438D 442D Caterpillar

Information:

Start By:a. remove oil pumpb. remove oil pan plate
3306 Engine Shown1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.
The connecting rod bolts are loose on the connecting rods and can fall out when the nuts are removed.
2. Push connecting rods (2) away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. The following steps are for the installation of the connecting rod bearings. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap.
3. Install the upper half of the rod bearing in the connecting rod, and put the connecting rod in position on the crankshaft.4. Install the lower half of the rod bearing in the connecting rod cap. For complete details concerning measuring bearing clearances, see Engine Bearings & Crankshafts, SEBD0531.5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put clean engine oil on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position. 8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft). Put a mark on each nut and the end of each bolt. Tighten the nuts 90 degrees more. Remove the connecting rod caps. Remove Plastigage (A), and measure the thickness of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps, and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump