CYLINDER GP-HOIST 2262031 - Caterpillar

Illustration 11 g06154713
Loosen clamp (17). Remove hose (16) from adapter (15). Plug hose with Tool (R) to limit oil leakage.
Remove adapter (12) from tee (14). Remove adapter (15) from the tee.
Remove tee (14) from the vibratory motor.
Install adapter (12) in tee (14). Install adapter (15) in the tee.
Remove Tool (R) from hose (11). Install hose on adapter (12). Tighten clamp (13) on the hose and the adapter.
Remove Tool (R) from hose (16). Install the hose on adapter (15). Tighten clamp (17) on the hose and the adapter.
Install Tool (H) in the case drain port in the motor. Install Tool (J) in branch of tee (14).
Connect Tool (E) on inlet side of Tool (B) to Tool (H). Connect Tool (E) on outlet side of Tool (B) to Tool (J).
Move engine start switch (8) to the START position. Release the switch when the engine starts.
Place the engine in high idle.
Operate the hydraulic system until the oil temperature reaches the test temperature of 45 °C (113 °F).
Move parking brake switch (2) to the OFF position.
Illustration 12 g06154730
Use vibratory frequency switch (18) to set the vibratory system in the low frequency/high amplitude mode on both drums.Note: Two things indicate when the vibratory system is in the low frequency/high amplitude mode. First, "low frequency" will appear on the display. Second, one LED next to vibratory frequency switch (18) will be illuminated.
Illustration 13 g06154733
If necessary, use drum select switch (19) to select both drums.Note: Two things indicate when the machine is in both drums mode. First, "Vibe Drum Select Dual" will appear on the display. Second, both LEDs next to drum select switch (19) will be illuminated.
Set the vibratory system in the manual mode.
Illustration 14 g06154741
Select "Main Menu" (20) on the machine display.
Select "Machine Setup" (21).
Illustration 15 g06154742
Select "Vibe Turn On Speed" (22).
Illustration 16 g06154754
Select "Manual" mode (23).
Launch the Plus+1TM program on the computer to enable the vibe test mode.Note: First time users need to perform the tasks in the Communication and Connections Wizard. This wizard allows the Windows® operating system to recognize the USB device. Follow the on-screen instructions.
Illustration 17 g06154764
Click "Status" icon (24).
Check for "Active Codes" . Clear any open "Active Codes".
Check "Machine Control" (25).
Illustration 18 g06154766
Click "Hydraulics" (26).
Click "Vibe Test Mode" (27).
Illustration 19 g06154771
Click "Enable" icon (28) to enable the "Normal Vibe Test Mode".
When "Normal Vibe Test Mode" is in "Enabled" mode, the Plus+1TM program is launched.
Illustration 20 g06149988
Standard propel control lever
Illustration 21 g06149991
Optional propel control lever
Press vibratory control switch (29) on the propel lever. The vibratory control switch must be held in the ON position for at least 2 seconds for the vibratory system to actuate.
Read flow on Tool (B). The flow should be between 3. L/min (0.9 U.S. gal/min) to 9 L/min (2.3 US gpm).Note: Motor case drain flow cannot be adjusted. If the case drain flow is greater than 9 L/min (2.3 U.S. gal/min), determine the source of excess flow and repair. If the flow is less than 3.5 L/min (0.9 U.S. gal/min), inspect the flushing valve and orifices.
Use vibratory control switch (29) to stop the vibratory system.
Place the