2590459 CYLINDER GP-HYDRAULIC Caterpillar parts
D3G, D4G, D5G
Rating:
Alternative (cross code) number:
CA2590459
259-0459
2590459
CA2590459
259-0459
2590459
Weight: 57 pounds 25 kg.
Information:
BORE DIAMETER
69.85
mm
CLOSED LENGTH
743.5
mm
PIN SIZE CAP END
38.1
mm
PIN SIZE ROD EYE
38.1
mm
ROD DIAMETER
38.1
mm
STROKE
412.5
TYPE
THD GLAND
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
All States Hydraulic Angle Cylinder fits Caterpillar D3G D4G D5G 259-0459
All States Compatible with Caterpillar Crawler Dozer(s) D3G (s/n JMH2052-later, s/n BYR1324-later), D4G (s/n HYD1719-later, s/n TLX859-later), D5G (s/n WGB2701-later, s/n RKG2122-later) || Replaces Caterpillar OEM Number(s) 259-0459 || Bushings included || This cylinder ships w/ bracket on it - if the customer orders this part number the bracket will be used - the hose guard will bolt up to the cylinder using this bracket. This setup will also use lug in the center of the cyl for grease hose & fitting to connect.
All States Compatible with Caterpillar Crawler Dozer(s) D3G (s/n JMH2052-later, s/n BYR1324-later), D4G (s/n HYD1719-later, s/n TLX859-later), D5G (s/n WGB2701-later, s/n RKG2122-later) || Replaces Caterpillar OEM Number(s) 259-0459 || Bushings included || This cylinder ships w/ bracket on it - if the customer orders this part number the bracket will be used - the hose guard will bolt up to the cylinder using this bracket. This setup will also use lug in the center of the cyl for grease hose & fitting to connect.
RAParts 259-0459 Angle Cylinder w/Bushings**JMH2052-up, BYR1324-up, HYD1719-up, TLX859-
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
All States Hydraulic Angle Cylinder fits Caterpillar D3G D4G D5G 259-0459
All States Compatible with Caterpillar Crawler Dozer(s) D3G (s/n JMH2052-later, s/n BYR1324-later), D4G (s/n HYD1719-later, s/n TLX859-later), D5G (s/n WGB2701-later, s/n RKG2122-later) || Replaces Caterpillar OEM Number(s) 259-0459 || Bushings included || This cylinder ships w/ bracket on it - if the customer orders this part number the bracket will be used - the hose guard will bolt up to the cylinder using this bracket. This setup will also use lug in the center of the cyl for grease hose & fitting to connect.
All States Compatible with Caterpillar Crawler Dozer(s) D3G (s/n JMH2052-later, s/n BYR1324-later), D4G (s/n HYD1719-later, s/n TLX859-later), D5G (s/n WGB2701-later, s/n RKG2122-later) || Replaces Caterpillar OEM Number(s) 259-0459 || Bushings included || This cylinder ships w/ bracket on it - if the customer orders this part number the bracket will be used - the hose guard will bolt up to the cylinder using this bracket. This setup will also use lug in the center of the cyl for grease hose & fitting to connect.
Number on catalog scheme:
For full view, you need register
Information:
3054B Naturally Aspirated Engine
Illustration 1 g00642351
Note: The word "Front" or an arrow which is marked on the piston crown must be toward the front of the engine. If the piston crown is not marked, put the narrowest side of the piston crater toward the side of the engine with the fuel injection pump. The shortest distance between the edge of the piston crater and the edge of the piston is the narrowest side of the piston crater.Note: Ensure that the ring end gaps of all the piston rings have 120 degrees spacing from each other.Note: Refer to the Systems Operation, Testing and Adjusting Module, "General Information" topic for the location of the serial number plate. (1) Top piston ring Shape of the ring groove in the piston for top piston ring ... Parallel Shape of the top piston ring ... Parallel Width of the ring groove in the piston for the top piston ring ... 2.60 to 2.62 mm (0.102 to 0.103 inch) Thickness of the top piston ring ... 2.475 to 2.49 mm (0.097 to 0.098 inch) Clearance between the ends of the top piston ring in a cylinder without any wear ... 0.28 to 0.51 mm (0.011 to 0.020 inch)Note: When you install a piston ring, make sure that the word "TOP" is facing the top of the piston. New top piston rings have a red identification mark which must be on the left of the ring end gap when the top piston ring is installed on an upright piston. (2) Intermediate piston ring Width of the groove in the piston for the intermediate piston ring ... 2.56 to 2.58 mm (0.101 to 0.102 inch) Thickness of the intermediate piston ring ... 2.48 to 2.49 mm (0.097 to 0.098 inch) Clearance between the ring groove in the piston and the intermediate piston ring ... 0.07 to 0.11 mm (0.003 to 0.004 inch) Clearance between the ends of an intermediate piston ring in a cylinder without any wear ... 0.30 to 0.63 mm (0.012 to 0.025 inch)Note: When you install a piston ring, make sure that the word "TOP" is facing the top of the piston. New intermediate rings have a green identification mark which must be on the left of the ring gap when the intermediate ring is installed on an upright piston. (3) Oil control ring Width of the ring groove in the piston for
Illustration 1 g00642351
Note: The word "Front" or an arrow which is marked on the piston crown must be toward the front of the engine. If the piston crown is not marked, put the narrowest side of the piston crater toward the side of the engine with the fuel injection pump. The shortest distance between the edge of the piston crater and the edge of the piston is the narrowest side of the piston crater.Note: Ensure that the ring end gaps of all the piston rings have 120 degrees spacing from each other.Note: Refer to the Systems Operation, Testing and Adjusting Module, "General Information" topic for the location of the serial number plate. (1) Top piston ring Shape of the ring groove in the piston for top piston ring ... Parallel Shape of the top piston ring ... Parallel Width of the ring groove in the piston for the top piston ring ... 2.60 to 2.62 mm (0.102 to 0.103 inch) Thickness of the top piston ring ... 2.475 to 2.49 mm (0.097 to 0.098 inch) Clearance between the ends of the top piston ring in a cylinder without any wear ... 0.28 to 0.51 mm (0.011 to 0.020 inch)Note: When you install a piston ring, make sure that the word "TOP" is facing the top of the piston. New top piston rings have a red identification mark which must be on the left of the ring end gap when the top piston ring is installed on an upright piston. (2) Intermediate piston ring Width of the groove in the piston for the intermediate piston ring ... 2.56 to 2.58 mm (0.101 to 0.102 inch) Thickness of the intermediate piston ring ... 2.48 to 2.49 mm (0.097 to 0.098 inch) Clearance between the ring groove in the piston and the intermediate piston ring ... 0.07 to 0.11 mm (0.003 to 0.004 inch) Clearance between the ends of an intermediate piston ring in a cylinder without any wear ... 0.30 to 0.63 mm (0.012 to 0.025 inch)Note: When you install a piston ring, make sure that the word "TOP" is facing the top of the piston. New intermediate rings have a green identification mark which must be on the left of the ring gap when the intermediate ring is installed on an upright piston. (3) Oil control ring Width of the ring groove in the piston for
Caterpillar SIS machinery equipment:
Caterpillar SIS
D3G XL & D3G LGP Track-Type Tractors BYR00001-UP (MACHINE) POWERED BY 3046 Engine »
259-0459
CYLINDER GP-HYDRAULIC
D4G XL & D4G LGP Track-Type Tractors HYD00001-UP (MACHINE) POWERED BY 3046 Engine »
259-0459
CYLINDER GP-HYDRAULIC
D5G XL & D5G LGP Track-Type Tractors RKG00001-UP (MACHINE) POWERED BY 3046 Engine »
259-0459
CYLINDER GP-HYDRAULIC
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
D3G, D4G, D5G
2465432
CYLINDER HEAD AS
315C, 317B LN, 318B, D3G, D4G, D5C III, D5G
315C, 317B LN, 318B, D3G, D4G, D5C III, D5G
315C, 315D L, D3G, D4G, D5G
2590460
CYLINDER GP-ANGLING
315D L, D3G, D4G, D5G
315D L, D3G, D4G, D5G
1070978
CYLINDER HEAD AS
315, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
2167387
CYLINDER AS
315C, D3G, D4G, D5G
315C, D3G, D4G, D5G
1838643
CYLINDER AS
315C, 315D L, D3G, D4G, D5G
315C, 315D L, D3G, D4G, D5G
931C II, 933, 933C, D3C, D3C II, D3C III, D3G, D4C II, D4C III, D4G, PM-201, PM-565, PM-565B
1833722
CYLINDER AS
D3G, D4G, D5G
D3G, D4G, D5G
1920892
CYLINDER AS
D3G, D4G, D5G
D3G, D4G, D5G
1920894
CYLINDER AS
D3G, D4G, D5G
D3G, D4G, D5G
2590460
CYLINDER GP-ANGLING
315D L, D3G, D4G, D5G
315D L, D3G, D4G, D5G
621G, 623G, 627G, 735, 980G, C18, D8R II
10R3198
CYLINDER HEAD AS
621G, 623G, 627G, 735, 980G, C15, C18, D8R II
621G, 623G, 627G, 735, 980G, C15, C18, D8R II
3518446
CYLINDER GP-LIFT
990H, 990K
990H, 990K
3349998
CYLINDER GP-BOOM
312C L
312C L