2821537 CYLINDER GP-STICK Caterpillar parts
305.5D, 305.5E, 305C CR
Rating:
Alternative (cross code) number:
CA2821537
282-1537
2821537
CA2821537
282-1537
2821537
Weight: 103 pounds 47 kg.
MINI HYD EXCAVATOR,
This part in 4 request:
Show.
This information for suppliers only!
2023-10-27
2023-04-02
2021-10-06
2019-08-08
Information:
The Cat ID will go through a sequence of screens when first powered up. Each of these screens is intended to provide set-up information to the driver before driving the vehicle. Cat ID will proceed through each screen, after displaying the screen for 3 seconds.It is recommended the power-up sequence be completed with all desired set-up information entered, and a desired information screen selected before driving the vehicle. An Active Diagnostic Code indicating a potentially seriouis engine problem will be automatically displayed by Cat ID and override the normal power-up sequence.
Depending on truck configuration, the engine may shut down when a potentially serious engine problem diagnostic code becomes active. The operator will be provided a warning indication 20 seconds before engine shutdown.
To avoid a hazardous condition that may cause injury or death, steer the vehicle to a suitable location to stop immediately when the warning code appears.
A complete map of the screens follows in the Cat ID Screen Map section.Display Screen Sequence
Theft Deterrent
The second screen shown, following power-up, is the THEFT DETERRENT title screen. The Cat ID will indicate the current status of the THEFT DETERRENT System, enabled, auto-enabled, or disabled. If the system is enabled, a password must be entered to start the engine. Press any key to continue.Driver Entry (3176B, C-10, C-12, 3406E, C-15, and C-16 Engines Only)
If programmed, the Cat ID will indicate the last driver stored as the active driver in the system. If the Fleet Trip Segment has been reset, the display will indicate NO ACTIVE DRIVER. Press any key to continue.State Crossing (3176B, C-10, C-12, 3406E, C-15, and C-16 Engines Only)
If programmed, this screen is the STATE CROSSING title screen. This indicates the last state stored as the current state in the system. If the Fleet Trip Segment has been reset, the display will indicate NO ACTIVE STATE. Press any key to continue.PM1 Maintenance
The final screen is a PM1 MAINTENANCE screen. This indicates when PM1 (oil and filter change) maintenance is due within 3000 miles/60 hours, or past due.Following the power-up sequence, the Cat ID will display the Miles Per Gallon screen under the INSTANTANEOUS DATA title screen. The driver can then go to the appropriate screen to enter the theft deterrent password, driver identification, and or state as necessary. The driver should then select the desired screen for viewing while driving, before starting the trip.
Whenever possible, the desired display selection should be made prior to operating the vehicle. Do not manipulate the display while the vehicle is moving. This could divert attention from driving efforts and result in personal injury or equipment damage.
Depending on truck configuration, the engine may shut down when a potentially serious engine problem diagnostic code becomes active. The operator will be provided a warning indication 20 seconds before engine shutdown.
To avoid a hazardous condition that may cause injury or death, steer the vehicle to a suitable location to stop immediately when the warning code appears.
A complete map of the screens follows in the Cat ID Screen Map section.Display Screen Sequence
Theft Deterrent
The second screen shown, following power-up, is the THEFT DETERRENT title screen. The Cat ID will indicate the current status of the THEFT DETERRENT System, enabled, auto-enabled, or disabled. If the system is enabled, a password must be entered to start the engine. Press any key to continue.Driver Entry (3176B, C-10, C-12, 3406E, C-15, and C-16 Engines Only)
If programmed, the Cat ID will indicate the last driver stored as the active driver in the system. If the Fleet Trip Segment has been reset, the display will indicate NO ACTIVE DRIVER. Press any key to continue.State Crossing (3176B, C-10, C-12, 3406E, C-15, and C-16 Engines Only)
If programmed, this screen is the STATE CROSSING title screen. This indicates the last state stored as the current state in the system. If the Fleet Trip Segment has been reset, the display will indicate NO ACTIVE STATE. Press any key to continue.PM1 Maintenance
The final screen is a PM1 MAINTENANCE screen. This indicates when PM1 (oil and filter change) maintenance is due within 3000 miles/60 hours, or past due.Following the power-up sequence, the Cat ID will display the Miles Per Gallon screen under the INSTANTANEOUS DATA title screen. The driver can then go to the appropriate screen to enter the theft deterrent password, driver identification, and or state as necessary. The driver should then select the desired screen for viewing while driving, before starting the trip.
Whenever possible, the desired display selection should be made prior to operating the vehicle. Do not manipulate the display while the vehicle is moving. This could divert attention from driving efforts and result in personal injury or equipment damage.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
3830517
CYLINDER HEAD AS
304E, 305.5E, 305E, 902C, 903C
304E, 305.5E, 305E, 902C, 903C
3830488
CYLINDER BLOCK AS
304E, 305.5E, 305E, 902C, 903C
304E, 305.5E, 305E, 902C, 903C
2704714
CYLINDER GP-BLADE
304, 304C CR, 305, 305.5D, 305C CR, 305D CR
304, 304C CR, 305, 305.5D, 305C CR, 305D CR
2839115
CYLINDER AS
304, 304C CR, 305, 305.5D, 305C CR, 305D CR
304, 304C CR, 305, 305.5D, 305C CR, 305D CR
2725690
CYLINDER AS
304C CR, 305.5D, 305.5E, 305C CR, 305D CR
304C CR, 305.5D, 305.5E, 305C CR, 305D CR
2725688
CYLINDER AS
304C CR, 305.5D, 305C CR, 305D CR
304C CR, 305.5D, 305C CR, 305D CR
2725646
CYLINDER AS
305.5D, 305.5E, 305C CR
305.5D, 305.5E, 305C CR
2725685
CYLINDER AS
305.5D, 305.5E, 305C CR
305.5D, 305.5E, 305C CR
2725667
CYLINDER AS
305.5D, 305.5E, 305C CR
305.5D, 305.5E, 305C CR
3920550
CYLINDER AS
305.5E, 305E
305.5E, 305E
3782513
CYLINDER AS-BOOM
305.5E, 305E
305.5E, 305E
3892613
CYLINDER AS-BOOM
305.5E
305.5E
3621165
CYLINDER BLOCK AS
G3516H
G3516H
7Y4974
CYLINDER & SEAL GP-CTWT
350, 350 L, 375, 375 L
350, 350 L, 375, 375 L
4350781
CYLINDER & LINES GP-BOOM
308E2 CR
308E2 CR
2034379
CYLINDER GP-HYDRAULIC
RM-300, RM-350B, RM-500
RM-300, RM-350B, RM-500
3459805
CYLINDER GP-BOWL
621H, 621K, 627H, 627K, 627K LRC
621H, 621K, 627H, 627K, 627K LRC
1011207
CYLINDER HEAD GP
3508, 3512, 3516
3508, 3512, 3516