2897975 CYLINDER GP-BUCKET Caterpillar parts
324D, 324D FM, 324D L, 324D LN
Rating:
Alternative (cross code) number:
CA2897975
289-7975
2897975
CA2897975
289-7975
2897975
Weight: 507 pounds 229 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$56.95
17 Apr 2022
Amazon.com
Kit King - CAT Caterpillar 1799772 Aftermarket Hydraulic Cylinder Seal Kit
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equip. Models: 320BBLBNBS, 320CCLCLNCS, 322B LBLNCCLCLN, 324DDLDLN, 325CCLCLN, 345B II, 365BB IIBLCC L, 374DL, 374FL, M318C, M318D, M325C, M325DL MH, M325D LM & More || Typical Hydraulic Applications: Boom, Bucket, Counterweight, Stick. Fits Caterpillar Cylinder Models: 1505913, 1772440, 1772446, 1799764 and… || Cylinders Continued: 2114828, 2336960, 2426855, 2897887, 2897901, 2897975, 2963235, 2963236, 2963238, 2963255, 3676466, 3676474, 3676475, 3676477, 3683243, 3683244, 3683246 and More
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equip. Models: 320BBLBNBS, 320CCLCLNCS, 322B LBLNCCLCLN, 324DDLDLN, 325CCLCLN, 345B II, 365BB IIBLCC L, 374DL, 374FL, M318C, M318D, M325C, M325DL MH, M325D LM & More || Typical Hydraulic Applications: Boom, Bucket, Counterweight, Stick. Fits Caterpillar Cylinder Models: 1505913, 1772440, 1772446, 1799764 and… || Cylinders Continued: 2114828, 2336960, 2426855, 2897887, 2897901, 2897975, 2963235, 2963236, 2963238, 2963255, 3676466, 3676474, 3676475, 3676477, 3683243, 3683244, 3683246 and More
Number on catalog scheme:
3
For full view, you need register
Compatible equipment models: 2897975:
Information:
3200, 3300, 3400, 3500 Series EnginesThe new seal groups are quite different from the former standard lip-type seals. The difference is the hydrodynamic grooves in the sealing lip of the new seal. These grooves in the seal lip move lubrication oil back into the engine crankcase as the crankshaft turns. Because of this seal lip design, the front seal for an engine is different from the rear seal group. The installed position of the seal lip grooves is important, because the grooves are very sensitive to the direction of crankshaft rotation. Each seal is marked with an arrow to show the direction of shaft rotation for which the seal can be used. If a specific seal group is installed on the wrong end of an engine, lubrication oil can actually be taken out of an engine, because the grooves in the seal lip are in the wrong direction in relation to crankshaft rotation. Special handling procedures and seal installation instructions for specific engines are given on the pages that follow.1 Use The Correct Tools For Seal Group Installation
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Caterpillar SIS machinery equipment:
Caterpillar SIS
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine »
289-7975
CYLINDER GP-BUCKET
324D L Excavator T2D00001-UP (MACHINE) POWERED BY C-7 Engine »
289-7975
CYLINDER GP-BUCKET
324D L Hydraulic Excavator JJG00001-UP (MACHINE) POWERED BY C-7 Engine »
289-7975
CYLINDER GP-BUCKET
324D FM JKR00001-UP (MACHINE) POWERED BY C7 Engine »
289-7975
CYLINDER GP-BUCKET
324D L Excavator LAB00001-UP (MACHINE) POWERED BY C7 Engine »
289-7975
CYLINDER GP-BUCKET
324D LN Mobile Hydraulic Power Unit KJR00001-UP (MACHINE) POWERED BY C7 Engine »
289-7975
CYLINDER GP-BUCKET
324D L Excavator PYT00001-UP (MACHINE) POWERED BY C7 Engine »
289-7975
CYLINDER GP-BUCKET
324D L & 324D LN Excavators BTK00001-UP (MACHINE) POWERED BY C7 Engine »
289-7975
CYLINDER GP-BUCKET
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 525C, 535C, 545...
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D...
324D, 324D FM, 324D L, 324D LN
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 326D L
3154452
CYLINDER AS
324D, 324D L, 324D LN, 325D, 325D L, 329D L, 329D LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 340D2 L, 345C L, 385C, 385C L
324D, 324D L, 324D LN, 325D, 325D L, 329D L, 329D LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 340D2 L, 345C L, 385C, 385C L
2798110
CYLINDER AS
324D, 324D LN, 324E LN, 325D, 325D L, 329D LN
324D, 324D LN, 324E LN, 325D, 325D L, 329D LN
2478798
CYLINDER AS
324D, 324D FM, 324D L, 324D LN
324D, 324D FM, 324D L, 324D LN
2897968
CYLINDER AS-HYDRAULIC
324D, 324D FM, 324D L, 324D LN
324D, 324D FM, 324D L, 324D LN
2837505
CYLINDER GP-BUCKET
320D, 324D L, 325B L, 325C, 325D L, 329D L
320D, 324D L, 325B L, 325C, 325D L, 329D L
2837506
CYLINDER GP-BUCKET
320D, 324D L, 325B L, 325C, 325D L, 329D L
320D, 324D L, 325B L, 325C, 325D L, 329D L
1434850
CYLINDER GP-HOIST
D350E, D400E
D350E, D400E
1501332
CYLINDER BLOCK GP
416B, 428B
416B, 428B
2495631
CYLINDER BLOCK GP
385B, 5090B
385B, 5090B
1426026
CYLINDER & MTG GP-HOIST
D400E II
D400E II
1854677
CYLINDER & MTG GP-STEERING
AD45, AE40 II
AD45, AE40 II
3596040
CYLINDER & LINES GP-BOOM
2384C, 559C
2384C, 559C
3199371
CYLINDER HEAD AS
303.5D, 303C CR
303.5D, 303C CR