3082467 CYLINDER GP-TILT Caterpillar parts
D11R, D11T
Rating:
Alternative (cross code) number:
CA3082467
308-2467
3082467
CA3082467
308-2467
3082467
Weight: 1322 pounds 599 kg.
TRACK-TYPE TRACTOR,
Information:
Introduction
The proportional reducing valve for the power shift pressure is located on the main pump housing. The proportional reducing valve sends the reduced pilot oil pressure to the regulators at the idler pump and the drive pump. The output flow of the idler pump and the drive pump is controlled in accordance with the power shift pressure. Power shift pressure is controlled by the machine ECM.Required Tools
Illustration 1 g01623868
Tooling group "B" 198-4240 Digital Pressure Indicator Gp
Table 1
Tool    Item    Part Number    Description    Qty    
B     198-4240     Digital Pressure Indicator Gp        
    B1     198-4234     Indicator     1    
B2 198-4237     Pressure Sensor
3445 kPa (500 psi)     1    
B3 198-4236     Extension Cable     1    Machine Preparation
The following procedure must be completed before performing the calibration.
Set the pilot pressure to the specifications in Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust" for the machine.
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Illustration 2 g02639756
Pressure tap for the proportional reducing valve (power shift pressure)
Connect a 3445 kPa (500 psi) pressure sensor to the pressure tap for power shift pressure.
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).Calibration Procedure
Enter the service mode. Input the password "9992".
Illustration 3 g02306455
Select "Power Shift Pressure" from the "Calibrations" menu.
Press the OK key in order to start the calibration. The engine RPM will automatically increase to the equivalence of engine speed dial 10.
Confirm the notes on the monitor display. Set up the test conditions in accordance with the instructions. Press the OK key.
Illustration 4 g02542459
Use the arrows to adjust the pressure until the pressure reading for power shift pressure is at 500 50 kPa (73 7 psi). Press the OK key.
Illustration 5 g02542476
Use the arrows to adjust the pressure until the pressure reading for power shift pressure is at 2500 50 kPa (363 7 psi). Press the OK key.
Illustration 6 g02542496
If calibration was successful and no errors occurred, the display will indicate that the calibration is complete.
Illustration 7 g02542497
The "Error" screen will be displayed on the monitor if an error occurs. The process of calibration will not be saved and the process must be restarted.
The proportional reducing valve for the power shift pressure is located on the main pump housing. The proportional reducing valve sends the reduced pilot oil pressure to the regulators at the idler pump and the drive pump. The output flow of the idler pump and the drive pump is controlled in accordance with the power shift pressure. Power shift pressure is controlled by the machine ECM.Required Tools
Illustration 1 g01623868
Tooling group "B" 198-4240 Digital Pressure Indicator Gp
Table 1
Tool    Item    Part Number    Description    Qty    
B     198-4240     Digital Pressure Indicator Gp        
    B1     198-4234     Indicator     1    
B2 198-4237     Pressure Sensor
3445 kPa (500 psi)     1    
B3 198-4236     Extension Cable     1    Machine Preparation
The following procedure must be completed before performing the calibration.
Set the pilot pressure to the specifications in Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust" for the machine.
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Illustration 2 g02639756
Pressure tap for the proportional reducing valve (power shift pressure)
Connect a 3445 kPa (500 psi) pressure sensor to the pressure tap for power shift pressure.
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).Calibration Procedure
Enter the service mode. Input the password "9992".
Illustration 3 g02306455
Select "Power Shift Pressure" from the "Calibrations" menu.
Press the OK key in order to start the calibration. The engine RPM will automatically increase to the equivalence of engine speed dial 10.
Confirm the notes on the monitor display. Set up the test conditions in accordance with the instructions. Press the OK key.
Illustration 4 g02542459
Use the arrows to adjust the pressure until the pressure reading for power shift pressure is at 500 50 kPa (73 7 psi). Press the OK key.
Illustration 5 g02542476
Use the arrows to adjust the pressure until the pressure reading for power shift pressure is at 2500 50 kPa (363 7 psi). Press the OK key.
Illustration 6 g02542496
If calibration was successful and no errors occurred, the display will indicate that the calibration is complete.
Illustration 7 g02542497
The "Error" screen will be displayed on the monitor if an error occurs. The process of calibration will not be saved and the process must be restarted.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D11R Carrydozer Track-Type Tractor AAF00001-UP (MACHINE) POWERED BY 3508B Engine »
308-2467
CYLINDER GP-TILT
D11T CARRYDOZER TRACK-TYPE TRACTOR TPB00001-UP (MACHINE) POWERED BY C32 Engine »
308-2467
CYLINDER GP-TILT
D11T CARRYDOZER TRACK-TYPE TRACTOR JNS00001-UP (MACHINE) POWERED BY C32 Engine »
308-2467
CYLINDER GP-TILT
D11T CARRYDOZER TRACK-TYPE TRACTOR MDG00001-UP (MACHINE) POWERED BY C32 Engine »
308-2467
CYLINDER GP-TILT
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
3172440
CYLINDER HEAD GP
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H,...
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H,...
6E3113
CYLINDER GP-RIPPER PIN PULLER
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
2425328
CYLINDER HEAD AS
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H...
2014257
CYLINDER HEAD GP
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 789C, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, D11R, PM3508, PM3512, PM3516, PP3516, ...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 789C, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, D11R, PM3508, PM3512, PM3516, PP3516, ...
6E6175
CYLINDER
416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 725, 730, 769D, 771D, 773D, 775D, 844, 990, 990 II, D11R, D250E II, D300E II, TH103, TH48-E70
416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 725, 730, 769D, 771D, 773D, 775D, 844, 990, 990 II, D11R, D250E II, D300E II, TH103, TH48-E70
6E3264
CYLINDER
416C, 416D, 420D, 426C, 430D, 436C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K...
416C, 416D, 420D, 426C, 430D, 436C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K...
7X1062
CYLINDER AS-ETHER
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
6E3976
CYLINDER AS
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
1115693
CYLINDER AS
D11R, D11T
D11R, D11T
1348242
CYLINDER AS
D11R, D11T
D11R, D11T
3672260
CYLINDER AS-TILT
854G, 854K, D11R, D11T
854G, 854K, D11R, D11T
3672261
CYLINDER AS-TILT
854G, 854K, D11R, D11T
854G, 854K, D11R, D11T
3082465
CYLINDER GP-TILT
D11R, D11T
D11R, D11T
1429196
CYLINDER GP-LIFT
236, 248, 267
236, 248, 267
1525306
CYLINDER GP-TILT
924G, 924GZ, 924H, 924HZ
924G, 924GZ, 924H, 924HZ
1783720
CYLINDER GP-COUPLER
924G, 924GZ
924G, 924GZ
1844612
CYLINDER BLOCK GP
924G, 924GZ
924G, 924GZ