3197268 CYLINDER HEAD AS Caterpillar parts
3011C, C1.1, CB-14
Rating:
Alternative (cross code) number:
CA3197268
319-7268
3197268
CA3197268
319-7268
3197268
Weight: 23 pounds 10 kg.
INDUSTRIAL ENGINE, VIBRATORY COMPACTOR,
You can buy:
US$595.00
29 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Complete Cylinder Head 319-7268 3197268 Compatible for Caterpillar CAT Engine C1.1 3011C C2.2
UOYETIB Part Number: CA3197268 319-7268 3197268 || Part Name: Complete Cylinder Head || Application: Compatible for Caterpillar CAT Engine: C1.1, 3011C, C2.2 Loader: 216B3 Excavator: 301.5, 301.6, 301.7CR, 301.8, 302 CR Compactor: CB1.7, CB1.8, CB14, CB34B, CB36B, CC34B, CB34B XW Generator: DE9.5E3 || Note: Application information provided is for reference only. Please make sure to match the exact part numbers between this part and the part that you are replacing. || Ask your mechanics to make sure it matches exactly in case of doubt before purchasing. Made of high-quality materials, stable performance, high reliability, easy to install, fast response.
UOYETIB Part Number: CA3197268 319-7268 3197268 || Part Name: Complete Cylinder Head || Application: Compatible for Caterpillar CAT Engine: C1.1, 3011C, C2.2 Loader: 216B3 Excavator: 301.5, 301.6, 301.7CR, 301.8, 302 CR Compactor: CB1.7, CB1.8, CB14, CB34B, CB36B, CC34B, CB34B XW Generator: DE9.5E3 || Note: Application information provided is for reference only. Please make sure to match the exact part numbers between this part and the part that you are replacing. || Ask your mechanics to make sure it matches exactly in case of doubt before purchasing. Made of high-quality materials, stable performance, high reliability, easy to install, fast response.
FridayParts Complete Cylinder Head 319-7268 3197268 Compatible for Caterpillar CAT Engine C1.1 3011C C2.2 Replacement
FP FRIDAYPARTS New aftermarket parts; the picture is just for reference || Part Number:CA3197268, 319-7268, 3197268 || Compatible for Caterpillar CAT Engine C1.1 3011C C2.2 || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
FP FRIDAYPARTS New aftermarket parts; the picture is just for reference || Part Number:CA3197268, 319-7268, 3197268 || Compatible for Caterpillar CAT Engine C1.1 3011C C2.2 || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
Compatible equipment models: 3197268:
Information:
Engine Runs Smoothly
Too Much Black Or Gray Exhaust Smoke 1. Poor Quality FuelIf poor or low quality fuel is suspected, use a source of known good quality fuel, and prime and start the engine. If the problem is resolved, drain the complete fuel system, replace the fuel filter, and add fuel recommended by Caterpillar.2. Fuel Injection Timing Out Of CalibrationCheck the fuel injection timing calibration and make necessary adjustments. See the topics, Engine Test Procedure Number P-402, [Checking Electronic Injection Timing With The Timing Adapter Tool Group And The ECAP (Electronic Control Analyzer and Programmer)], and Engine Test Procedure Number P-403, [Calibrating Electronic Injection Timing With The Timing Adapter Tool Group And The ECAP (Electronic Control Analyzer and Programmer)], in Electronic Troubleshooting, 3176 Diesel Truck Engine, Form No. SENR3913.3. Air Inlet Piping Damage Or RestrictionVisually inspect the air inlet system for damage or restriction. If leaks are found, repair or replace parts as required.If the air cleaner has an Air Cleaner Service Indicator, check the indicator for the position of the red piston. If the indicator shows red at any time, install a clean or new air cleaner element.Air inlet restriction can be checked with a water manometer or a vacuum gauge [measuring mm (inches) of water]. Make a connection to the piping between the air cleaner and the inlet to the turbocharger. The maximum restriction allowed, with the engine at full load rpm, is 635 mm (25 in) of water. If a water manometer or vacuum gauge is not available, visually check the air filter for dirt. Clean or replace as required.4. Exhaust System RestrictionVisually inspect the exhaust system for damage or restriction. If leaks are found, repair or replace parts as required.Exhaust system back pressure (pressure differential between the turbocharger exhaust outlet and atmosphere) should not exceed 1016 mm (40 in) of water. An alternative check would be to remove the exhaust piping, load the engine on a chassis dynamometer to determine if the problem is corrected. If this solves the problem, the restriction is in the muffler or truck piping.5. Valve Adjustment Not CorrectCheck and make any necessary adjustments. See the topic, Valve Clearance Setting, in 3176 Diesel Truck Engine Systems Operation And Testing and Adjusting, Form No. SENR3909. Intake valve clearance is 0.38 mm (.015 in), and exhaust valve clearance is 0.64 mm (.025 in).6. Defective Unit InjectorsA defective unit injector can be found, by running the engine at the rpm where the problem exists, with the use of the Electronic Control Analyzer and Programmer (ECAP) service tool Interactive Diagnostics feature (single cylinder cutout) to stop the fuel supply to each cylinder in turn. If a cylinder is found where the cutout makes no difference on the engine performance, that injector should be removed and tested. Drain the fuel supply manifold and remove the injector(s) (see 3176 Diesel Truck Engine Disassembly and Assembly, Form No. SENR3914).Testing of the injectors must be done off of the engine. Use the 1U6661 Pop (Injector) Tester Group with
Too Much Black Or Gray Exhaust Smoke 1. Poor Quality FuelIf poor or low quality fuel is suspected, use a source of known good quality fuel, and prime and start the engine. If the problem is resolved, drain the complete fuel system, replace the fuel filter, and add fuel recommended by Caterpillar.2. Fuel Injection Timing Out Of CalibrationCheck the fuel injection timing calibration and make necessary adjustments. See the topics, Engine Test Procedure Number P-402, [Checking Electronic Injection Timing With The Timing Adapter Tool Group And The ECAP (Electronic Control Analyzer and Programmer)], and Engine Test Procedure Number P-403, [Calibrating Electronic Injection Timing With The Timing Adapter Tool Group And The ECAP (Electronic Control Analyzer and Programmer)], in Electronic Troubleshooting, 3176 Diesel Truck Engine, Form No. SENR3913.3. Air Inlet Piping Damage Or RestrictionVisually inspect the air inlet system for damage or restriction. If leaks are found, repair or replace parts as required.If the air cleaner has an Air Cleaner Service Indicator, check the indicator for the position of the red piston. If the indicator shows red at any time, install a clean or new air cleaner element.Air inlet restriction can be checked with a water manometer or a vacuum gauge [measuring mm (inches) of water]. Make a connection to the piping between the air cleaner and the inlet to the turbocharger. The maximum restriction allowed, with the engine at full load rpm, is 635 mm (25 in) of water. If a water manometer or vacuum gauge is not available, visually check the air filter for dirt. Clean or replace as required.4. Exhaust System RestrictionVisually inspect the exhaust system for damage or restriction. If leaks are found, repair or replace parts as required.Exhaust system back pressure (pressure differential between the turbocharger exhaust outlet and atmosphere) should not exceed 1016 mm (40 in) of water. An alternative check would be to remove the exhaust piping, load the engine on a chassis dynamometer to determine if the problem is corrected. If this solves the problem, the restriction is in the muffler or truck piping.5. Valve Adjustment Not CorrectCheck and make any necessary adjustments. See the topic, Valve Clearance Setting, in 3176 Diesel Truck Engine Systems Operation And Testing and Adjusting, Form No. SENR3909. Intake valve clearance is 0.38 mm (.015 in), and exhaust valve clearance is 0.64 mm (.025 in).6. Defective Unit InjectorsA defective unit injector can be found, by running the engine at the rpm where the problem exists, with the use of the Electronic Control Analyzer and Programmer (ECAP) service tool Interactive Diagnostics feature (single cylinder cutout) to stop the fuel supply to each cylinder in turn. If a cylinder is found where the cutout makes no difference on the engine performance, that injector should be removed and tested. Drain the fuel supply manifold and remove the injector(s) (see 3176 Diesel Truck Engine Disassembly and Assembly, Form No. SENR3914).Testing of the injectors must be done off of the engine. Use the 1U6661 Pop (Injector) Tester Group with
Caterpillar SIS machinery equipment:
Caterpillar SIS
CB14 Vibratory Utility Compactor DTT00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
CB34B Compactor 42300001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CB34B XW Compactor 42500001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CC34B Compactor 32400001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CB34B Compactor 3B400001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CC34B Compactor CC300001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CB34B XW Compactor JTX00001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
CB36B Compactor M3600001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
DE9.5E3 Generator Set TYB00001-UP POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
CB1.8 Vibratory Utility Compactor ERX00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
CB1.7 Vibratory Utility Compactor HRB00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
301.6 Mini Hydraulic Excavator MY600001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
301.8 Mini Hydraulic Excavator H8X00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
301.7CR Mini Hydraulic Excavator JH700001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
301.5 Mini Hydraulic Excavator MNH00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
CB1.8 Vibratory Utility Compactor 64400001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
CB1.7 Vibratory Utility Compactor 64300001-UP (MACHINE) POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
3011C Industrial Engine 31100001-UP »
319-7268
CYLINDER HEAD AS
C1.1 Industrial Engine C3M00001-UP »
319-7268
CYLINDER HEAD AS
C1.1 Industrial Engine C6L00001-UP »
319-7268
CYLINDER HEAD AS
C1.1 Industrial Engine G8N00001-UP POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
C1.1 Industrial Engine C7Y00001-UP »
319-7268
CYLINDER HEAD AS
C1.1 350-3712 C6L00001-UP »
319-7268
CYLINDER HEAD AS
216B3 Skid Steer Loader HR200001-UP (MACHINE) POWERED BY C2.2 Engine »
319-7268
CYLINDER HEAD AS
DE9.5E3 Generator Set GB800001-UP POWERED BY C1.1 Engine »
319-7268
CYLINDER HEAD AS
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
3131957
CYLINDER BLOCK GP
3011C, C1.1, CB-14
3011C, C1.1, CB-14
3111099
CYLINDER BLOCK GP
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3111158
CYLINDER HEAD AS
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
2690676
CYLINDER BLOCK GP
3011C, C1.1
3011C, C1.1
2346036
CYLINDER BLOCK GP-LONG
3011C, C1.1
3011C, C1.1
2464340
CYLINDER BLOCK GP-LONG
3011C, C1.1
3011C, C1.1
2690691
CYLINDER HEAD GP
3011C, C1.1
3011C, C1.1
7J9730
CYLINDER GP-TILT
930, 930R
930, 930R
8J8458
CYLINDER GP-BAIL
627B, 637D, 657B, 657E
627B, 637D, 657B, 657E
3356218
CYLINDER HEAD GP
3508, 3512, 3516, PM3516
3508, 3512, 3516, PM3516
7N3336
CYLINDER HEAD GROUP
583K, D342, D342C, D8K
583K, D342, D342C, D8K
2836132
CYLINDER GP-BUCKET
318C, 319C, 320B, 320C, 325B L, 325C, 325D, 329D L, 330B L, 330C, 345B II, 345B L
318C, 319C, 320B, 320C, 325B L, 325C, 325D, 329D L, 330B L, 330C, 345B II, 345B L
2932086
CYLINDER HEAD GP
216B, 232B, 242B, 3024C
216B, 232B, 242B, 3024C
3672084
CYLINDER BLOCK GP
3054C, C4.4
3054C, C4.4
2370842
CYLINDER BLOCK GP
773F, 775F, 844H, 990H, AD55B, C27, D10N, D10R, D10T, TH48-E70
773F, 775F, 844H, 990H, AD55B, C27, D10N, D10R, D10T, TH48-E70
7N0841
CYLINDER BLOCK AS
3412, 651E, 657E, 772B, 773B, 775B, 990, 992C, 992D, D10N, D9L, G3412, PR-1000, PR-750B
3412, 651E, 657E, 772B, 773B, 775B, 990, 992C, 992D, D10N, D9L, G3412, PR-1000, PR-750B
1P6382
CYLINDER HEAD AS
594, D9G
594, D9G
4Z6363
CYLINDER GP-RIPPER
D9R, D9T
D9R, D9T