AVSPARE.COM
parts catalog

CYLINDER AS. 3236100 - Caterpillar



3236100 CYLINDER AS. Caterpillar parts CYLINDER
Rating:
31
Alternative (cross code) number:
CA3236100
323-6100
3236100
Caterpillar 3236100 CYLINDER AS.
Weight: 44 pounds 20 kg.

Buy CYLINDER AS. 3236100 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 4 g06059418
Use screed float switch (7) to place the screed in the FLOAT position. When the screed is in the FLOAT position, an LED next to the screed float switch will illuminate. Allow the screed to lower to the ground.
Press rpm decrease switch (8) once to operate the engine in low idle.
Illustration 5 g06007063
Examine the display. If "Regen Conditions Not Met" warning (9) is shown and the banner is yellow, allow the engine to operate until the regeneration cycle is complete. The cycle may require up to 1 hour to complete. If the warning banner is red, use Cat® ET to complete a regeneration cycle as soon as possible. If no engine regeneration warning is shown, go to the next step.
Illustration 6 g06059534
Press and hold push to start switch (10). Release the switch when the engine stops.
Illustration 7 g06059552
Move machine power switch (11) to the OFF position.
Illustration 8 g06061805
Open pump compartment door (12).
Illustration 9 g06078307
Disconnect hose (13).
Illustration 10 g06078318
Install Tool (B), and connect hose (13) to the tool.
Connect Tool (A2) to Tool (C).Test Procedure
Illustration 11 g06078323
Move machine power switch (11) into the ON position. After the home screen is shown on display (14), press, and hold push to start switch (10). Release the switch when the engine starts.
Illustration 12 g06078339
Actuate screen unlock switch (15) to enable the touch screen on the display.Note: When the display is enabled, an LED next to the screen unlock switch is illuminated.
Illustration 13 g06078356
Tap status icon (16) to enter the status screen.
Illustration 14 g06078364
Operate the engine at low idle for a few minutes. Press rpm increase switch (17) once to operate the engine in high idle.
Illustration 15 g06078372
Monitor the hydraulic oil temperature on display (18). Operate the machine until the oil temperature reaches a minimum of 45 10 °C (113 18 °F).
Actuate parking brake switch (5).
Use Tool (A) to record the pressure. The pressure should be zero to 500 kPa (73 psi).
Illustration 16 g06078381
Use travel mode switch (3) to select the travel mode. When the travel mode is set to travel, an LED next to travel symbol (19) is illuminated.
Use Tool (A) to record the pressure. The pressure specification is given in "Specifications" Table 2.
Press rpm decrease switch (8) once to operate the engine in low idle.Note: If necessary, perform a regeneration cycle before the engine is stopped.
Press and hold push to start switch (10). Release the switch when the engine stops.
Move machine power switch (11) to the OFF position.
If the pressure readings were not in the ranges given above, troubleshoot the electrical circuit to the shift solenoid and/or check the shift valve for oil restriction. If the pressure readings were inside the ranges given above, go to the next step.
Disconnect Tool (A2) from Tool (C).
Disconnect hose (13) from Tool (B). Remove Tool (B).
Connect hose (13) to the valve.
Close pump compartment door (12).


Parts cylinder Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.