3282293 CYLINDER AS-HYDRAULIC Caterpillar parts
D5R LGP, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, D6R III, D6T, D6T LGP, D6T XL
Rating:
Alternative (cross code) number:
CA3282293
328-2293
3282293
CA3282293
328-2293
3282293
Weight: 103 pounds 46 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 3282293:
Information:
Removal Procedure
Start By:
Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
Remove the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Remove the engine control module (ECM). Refer to Disassembly and Assembly, "Engine Control Module - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027496
Position engine speed/timing sensors (1) out of the way.
Remove side covers (2) .
Illustration 2 g01027497
Remove bolts (3) and the dowels that hold the lifter arms (4) and the lifter shaft (5) to each side cover. Remove gasket (6) .Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9S-3263     Thread Lock Compound     1    
B     1U-8846     Gasket Sealant     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01027497
Install gasket (6) .
Install lifter arms (4) on lifter shaft (5) .
Position lifter shaft (5) and the dowels on the side cover. Ensure that the oil holes in the lifter shaft are facing the side cover. Apply Tooling (A) on the threads of bolts (3). Install bolts (3). Tighten bolts (3) to a torque of 13 3 N m (10 2 lb ft). Tighten the center bolts. Then tighten the bolts on the end.
Lubricate the lifters with clean engine oil.
Apply Tooling (B) to the sealing surfaces of the side cover. The side covers must be installed on the cylinder block within 10 minutes of applying the sealant.
Illustration 4 g01027496
Position the gaskets and side covers (2) on the cylinder block. Install the bolts.
Install engine speed/timing sensors (1) .End By:
Install the engine control module (ECM). Refer to Disassembly and Assembly, "Engine Control Module - Remove and Install".
Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
Install the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
Start By:
Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
Remove the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Remove the engine control module (ECM). Refer to Disassembly and Assembly, "Engine Control Module - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027496
Position engine speed/timing sensors (1) out of the way.
Remove side covers (2) .
Illustration 2 g01027497
Remove bolts (3) and the dowels that hold the lifter arms (4) and the lifter shaft (5) to each side cover. Remove gasket (6) .Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9S-3263     Thread Lock Compound     1    
B     1U-8846     Gasket Sealant     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01027497
Install gasket (6) .
Install lifter arms (4) on lifter shaft (5) .
Position lifter shaft (5) and the dowels on the side cover. Ensure that the oil holes in the lifter shaft are facing the side cover. Apply Tooling (A) on the threads of bolts (3). Install bolts (3). Tighten bolts (3) to a torque of 13 3 N m (10 2 lb ft). Tighten the center bolts. Then tighten the bolts on the end.
Lubricate the lifters with clean engine oil.
Apply Tooling (B) to the sealing surfaces of the side cover. The side covers must be installed on the cylinder block within 10 minutes of applying the sealant.
Illustration 4 g01027496
Position the gaskets and side covers (2) on the cylinder block. Install the bolts.
Install engine speed/timing sensors (1) .End By:
Install the engine control module (ECM). Refer to Disassembly and Assembly, "Engine Control Module - Remove and Install".
Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
Install the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
3217048
CYLINDER GP-ANGLING
D6M, D6N
D6M, D6N
2280320
CYLINDER GP-ANGLING
D6M, D6N
D6M, D6N
1103269
CYLINDER GP-BULLDOZER LIFT
D5R LGP, D6M, D6N, D6N LGP
D5R LGP, D6M, D6N, D6N LGP
3679478
CYLINDER GP-TILT
D6R, D6R III, D6R STD, D6T, D6T LGP, D6T XL
D6R, D6R III, D6R STD, D6T, D6T LGP, D6T XL
7X1062
CYLINDER AS-ETHER
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
3147923
CYLINDER
517, 527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
517, 527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
1080801
CYLINDER
D5R LGP, D6M, D6N, D6N LGP, D6N OEM
D5R LGP, D6M, D6N, D6N LGP, D6N OEM
1103787
CYLINDER AS
12H, 12H NA, 140H, 140H NA, D6M, D6N
12H, 12H NA, 140H, 140H NA, D6M, D6N
1103270
CYLINDER AS
D5R LGP, D6M, D6N, D6N LGP
D5R LGP, D6M, D6N, D6N LGP
3217046
CYLINDER AS-HYDRAULIC
D6M, D6N
D6M, D6N
1776915
CYLINDER
906H, 906H2, 907H, 907H2, 908H, 908H2, CB-534C, CB-534D, CB-564D, CB-634C, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-531D, CS-533D, CS-56, CS-563D, CS-563E, CS-573D, CS-583D, CS-583E, CS-64, CS-663E, ...
906H, 906H2, 907H, 907H2, 908H, 908H2, CB-534C, CB-534D, CB-564D, CB-634C, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-531D, CS-533D, CS-56, CS-563D, CS-563E, CS-573D, CS-583D, CS-583E, CS-64, CS-663E, ...
2693238
CYLINDER AS
D6K, D6K LGP, D6K XL
D6K, D6K LGP, D6K XL
2693231
CYLINDER AS
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP
2693205
CYLINDER AS
D6K, D6K LGP, D6K XL
D6K, D6K LGP, D6K XL
2515785
CYLINDER
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
2951778
CYLINDER AS
D6K, D6K LGP, D6K XL, PL61
D6K, D6K LGP, D6K XL, PL61
2642353
CYLINDER AS
583T, PL83
583T, PL83
1051636
CYLINDER-CONTROL
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
2284024
CYLINDER AS
D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
3496043
CYLINDER AS
D6T LGP, D6T LGPPAT, D6T XL
D6T LGP, D6T LGPPAT, D6T XL
3496041
CYLINDER AS
D6T LGP, D6T XL
D6T LGP, D6T XL
2871991
CYLINDER AS
D6T, D6T LGP, D6T XL
D6T, D6T LGP, D6T XL
2821927
CYLINDER AS
587R, 587T, PL87
587R, 587T, PL87