3481153 CYLINDER AS Caterpillar parts
924K, 930K
Rating:
Alternative (cross code) number:
CA3481153
348-1153
3481153
CA3481153
348-1153
3481153
Weight: 26 pounds 12 kg.
WHEEL LOADER,
Information:
Illustration 1 g00439883
Number 1 Clutch Solenoid Modulating Valve SchematicCID 0631 FMI 06 service code is recorded when the power train electronic control module (ECM) reads the current of the solenoid circuit as above normal (short to ground). Note: Ensure that the service code CID 0631 FMI 06 for the solenoid is active. Before performing this procedure, refer to table 1 in order to determine the connector contact number and the wire number that corresponds to the failed circuit.
Table 1
Solenoid Valve Information    
Fault    Connector Contact No. (1)    Wire No.    
Number 1 Clutch Solenoid Modulating Valve (Reverse)     J1-17     751-GN    
( 1 ) Connector contact number of the power train ECM.Note: All of the solenoid return lines are joined and connect to contacts J1-7 and J2-3 (wire 975-WH).Note: The approximate coil resistance of the clutch solenoid modulating valves is 5 to 15 Ohms.Note: Access to the clutch solenoid modulating valve may require removal of the left rear platform support bracket. Replacement of the clutch solenoid modulating valve may require removal of the cab.
Check the resistance of the solenoid.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the suspected solenoid.
At the clutch solenoid modulating valve, measure the resistance between the two contacts of the solenoid connector.Expected Result: The resistance should be between 5 - 15 Ohms.Results:
OK - The solenoid resistance is correct. Proceed to Step 2.
NOT OK - The solenoid has failed. Replace the solenoid. STOP.
Check the solenoid for a short to ground.The disconnect switch and the key start switch remain in the OFF position. The solenoid remains disconnected from the machine harness.
Measure the resistance from each solenoid contact to frame ground.Expected Result: Each resistance should be greater than 5000 Ohms.Results:
OK - The solenoid and the solenoid harness are correct. The fault is in the machine harness. Proceed to Step 3.
NOT OK - The solenoid has failed. Replace the solenoid. STOP.
Check the machine harness for a short to ground.The machine harness remains disconnected from the solenoid.
The disconnect switch and the key start switch remain in the OFF position.
Disconnect the machine harness connectors J1 and J2 from the power train ECM.
At machine harness connector J1 or J2, measure the resistance from the solenoid signal contact (refer to table 1) to all possible sources of ground. The following contacts are possible ground sources: J1-2, J1-5, J1-7, J1-15, J1-16, J2-3 and frame ground.Expected Result: Each resistance should be greater than 5000 Ohms.Results:
OK - The machine harness is correct. Proceed to Step 4.
NOT OK - There is a short in the machine harness. The short is between the wire for the solenoid signal (refer to table 1) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness. STOP.
Check if the fault is still present.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Stop the machine and
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
3852572
CYLINDER HEAD GP
323D2 L, 535D, 545D, 924K, 930K, 938K, 950 GC, C7.1, D6K2
323D2 L, 535D, 545D, 924K, 930K, 938K, 950 GC, C7.1, D6K2
6E3264
CYLINDER
416C, 416D, 420D, 426C, 430D, 436C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K...
416C, 416D, 420D, 426C, 430D, 436C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K...
1925897
CYLINDER GP-COUPLER
924K, 930K, 938G, 938H, 938K, 950G II, 950H, 950K, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 973C, SW2003/6, SW2109
924K, 930K, 938G, 938H, 938K, 950G II, 950H, 950K, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 973C, SW2003/6, SW2109
1051636
CYLINDER-CONTROL
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
4518385
CYLINDER BLOCK GP-SHORT
924K, 930K, 938K, D6K2
924K, 930K, 938K, D6K2
3704106
CYLINDER AS-HYDRAULIC
924G, 924H, 924K, 928HZ, 930G, 930K, 938K
924G, 924H, 924K, 928HZ, 930G, 930K, 938K
3539375
CYLINDER GP-HYDRAULIC
924K, 930K, 938K, 950K, 962K, PW2503/7
924K, 930K, 938K, 950K, 962K, PW2503/7
3510949
CYLINDER AS
938K
938K
3539375
CYLINDER GP-HYDRAULIC
924K, 930K, 938K, 950K, 962K, PW2503/7
924K, 930K, 938K, 950K, 962K, PW2503/7