3521096 CYLINDER AS-BOOM Caterpillar parts
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
Rating:
Alternative (cross code) number:
CA3521096
352-1096
3521096
CA3521096
352-1096
3521096
Weight: 138 pounds 62 kg.
EXCAVATOR,
Compatible equipment models: 3521096:
Number on catalog scheme:
1
For full view, you need register
Information:
Possible causes for an FMI 9 diagnostic code are:
Terminating resistors on the J1939 Data Link are faulty.
An open or a poor connection in the circuit.
A short in the circuit.
An ECM or smart device is not powering up or powering down properly.
Lack of key switch input to an ECM or smart device.
Excessive noise on the circuit.
Software configuration mismatch.
One of the ECM modules has failed. This condition is unlikely.Possible causes for an FMI 14 diagnostic code are:
Incorrect software is installed.
Incompatible software may be installed.
Interference across the data link wires.
A control module has failed. This situation is unlikely.
Illustration 1 g03433898
Schematic of the CAN Datalink
Note: The diagram above is a simplified schematic of the CAN Datalink connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR1138 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active FMI Code Associated With The Data Link Code present FMI 9, proceed to Test Step 2.
FMI 14, proceed to Test Step 7.
Begin Process For FMI 9 Troubleshooting HERE
2. Check For Other Codes
A. Check for similar diagnostic codes that are logged against other electronic control modules.
B. If a similar diagnostic code is found, exit this test and perform the corresponding procedure for the other diagnostic code that is shown.
Another diagnostic code is showing. OK - Exit this procedure and perform the diagnostic procedure for the diagnostic codes that are shown.
Proceed to Test Step 8.
NOT OK - There are no other related diagnostic codes.
Proceed to Test Step 3.
3. Inspect The Harness Connections
A. Turn key start switch and disconnect switch OFF.
B. Inspect all harness connections related to the data link. Make sure that the connectors are clean and tight.
The machine harness is correct. OK - The machine harness is correct.
Proceed to Test Step 4.
NOT OK - The machine harness is not correct.
Repair: Repair
Terminating resistors on the J1939 Data Link are faulty.
An open or a poor connection in the circuit.
A short in the circuit.
An ECM or smart device is not powering up or powering down properly.
Lack of key switch input to an ECM or smart device.
Excessive noise on the circuit.
Software configuration mismatch.
One of the ECM modules has failed. This condition is unlikely.Possible causes for an FMI 14 diagnostic code are:
Incorrect software is installed.
Incompatible software may be installed.
Interference across the data link wires.
A control module has failed. This situation is unlikely.
Illustration 1 g03433898
Schematic of the CAN Datalink
Note: The diagram above is a simplified schematic of the CAN Datalink connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR1138 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active FMI Code Associated With The Data Link Code present FMI 9, proceed to Test Step 2.
FMI 14, proceed to Test Step 7.
Begin Process For FMI 9 Troubleshooting HERE
2. Check For Other Codes
A. Check for similar diagnostic codes that are logged against other electronic control modules.
B. If a similar diagnostic code is found, exit this test and perform the corresponding procedure for the other diagnostic code that is shown.
Another diagnostic code is showing. OK - Exit this procedure and perform the diagnostic procedure for the diagnostic codes that are shown.
Proceed to Test Step 8.
NOT OK - There are no other related diagnostic codes.
Proceed to Test Step 3.
3. Inspect The Harness Connections
A. Turn key start switch and disconnect switch OFF.
B. Inspect all harness connections related to the data link. Make sure that the connectors are clean and tight.
The machine harness is correct. OK - The machine harness is correct.
Proceed to Test Step 4.
NOT OK - The machine harness is not correct.
Repair: Repair
Cat SIS web machinery list:
Parts cylinder Caterpillar catalog:
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 324D, 324D L
320D, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
323D2 L, 535D, 545D, 924K, 930K, 938K, 950 GC, C7.1, D6K2
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L, 324D
320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 323D L
315D L, 318E L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D2 ...
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
4185509
CYLINDER AS
321D LCR
321D LCR
3521097
CYLINDER AS-BOOM
320E L
320E L
3568789
CYLINDER AS-HYDRAULIC
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L
3728279
CYLINDER-HYDRAULIC
320D FM, HH44 DE
320D FM, HH44 DE
3728278
CYLINDER-HYDRAULIC
320D FM, HH44 DE
320D FM, HH44 DE
2781195
CYLINDER AS
525C
525C
2886756
CYLINDER AS
525C
525C
2781766
CYLINDER AS
525C, 535C
525C, 535C
2886757
CYLINDER AS
525C, 535C
525C, 535C
2835985
CYLINDER AS
321D LCR
321D LCR
2835982
CYLINDER AS
321D LCR
321D LCR
3521099
CYLINDER AS-STICK
320D, 320D L, 320D2, 320D2 L, 323D L, 323D2 L
320D, 320D L, 320D2, 320D2 L, 323D L, 323D2 L
3521098
CYLINDER AS-STICK
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
3521101
CYLINDER AS-HYDRAULIC
320D, 320E, 320E RR
320D, 320E, 320E RR
3600074
CYLINDER AS
320D, 320D L, 320D2, 320D2 L, 320E LN, 323D L, 323D2 L, 323E L, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D L, 320D2, 320D2 L, 320E LN, 323D L, 323D2 L, 323E L, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN