3631685 CYLINDER GP-STICK Caterpillar parts
390F L
Rating:
Alternative (cross code) number:
CA3631685
363-1685
3631685
CA3631685
363-1685
3631685
Weight: 2449 pounds 1110 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 3631685 Stick Hydraulic Cylinder for Model 390F L
CTP For Model 390F L || Sold in each || Easy in-and-out fit || Country of origin: United States
CTP For Model 390F L || Sold in each || Easy in-and-out fit || Country of origin: United States
CTP 3631685 Stick Hydraulic Cylinder for Model 390F L
CTP For Model 390F L || Sold in each || Easy in-and-out fit || Country of origin: United States
CTP For Model 390F L || Sold in each || Easy in-and-out fit || Country of origin: United States
This part in 4 request:
Show.
This information for suppliers only!
2025-05-08
2021-02-22
2019-09-06
2017-11-23
Compatible equipment models: 3631685:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 352-5891 Lifting Strap 2
B Loctite 771 -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g02303775
Illustration 2 g02303794
Loosen clamp assembly (1) and position clamp assembly (1) out of the way.
Disconnect the cable assembly (not shown) from soot antennae (4).
Disconnect tube assembly (5) and remove temperature sensor (6).
Remove ball clamp (7). Attach Tooling (A) and a suitable lifting device to diesel oxidation catalyst (3). Disconnect clamp assembly (2) and remove the catalyst. The weight of catalyst (3) is approximately 21 kg (46 lb).
Discard clamp assembly (1). Installation Procedure
Install catalyst (3) in reverse order.
Install new clamp assembly (1). Apply Tooling (B) to the threads of clamp assembly (1). Tighten clamp assembly (1) to a torque of 50 2.5 N m (37 2 lb ft). Do not use power tools in order to tighten clamp assembly (1).
Illustration 3 g02303953
Illustration 4 g02303939
Verify that the cup of the ball joint (G) does not touch the radius of the ball (F). Position ball clamp (7) and hand tighten ball clamp (7). Ball Clamp (7) should be in the center of the joint. Dimension (C) and Dimension (D) should be equal within 2 mm (0.08 inch). Repeat the measurements every 90° around ball clamp (7). If necessary, adjust ball clamp (7). Do not use power tools in order to torque clamp assembly (7). Torque ball clamp (7) to a torque of 35 2 N m (26 1 lb ft).
Illustration 5 g02303555
Typical Example
Note: Ensure that clamp assembly (2) is centered in the cradle pin joint. Align the clamp assembly uniformly over the diesel oxidation catalyst prior to the tightening of the clamp assembly.
Apply Tooling (B) to the threads of clamp assembly (2) for a Distance (X). Distance (X) is 25 mm (1 inch) above the trunnion. Use hand tools in order to tighten clamp assembly (2). Tighten clamp assembly (2) to a torque of 16.5 1.5 N m (146 13 lb in).
Apply Tooling (B) to temperature sensor (6). Tighten temperature sensor (6) to a torque of 45 5 N m (33 4 lb ft).
Connect the cable assembly (not shown) to soot antennae (4) and hand tighten the cable assembly.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 352-5891 Lifting Strap 2
B Loctite 771 -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g02303775
Illustration 2 g02303794
Loosen clamp assembly (1) and position clamp assembly (1) out of the way.
Disconnect the cable assembly (not shown) from soot antennae (4).
Disconnect tube assembly (5) and remove temperature sensor (6).
Remove ball clamp (7). Attach Tooling (A) and a suitable lifting device to diesel oxidation catalyst (3). Disconnect clamp assembly (2) and remove the catalyst. The weight of catalyst (3) is approximately 21 kg (46 lb).
Discard clamp assembly (1). Installation Procedure
Install catalyst (3) in reverse order.
Install new clamp assembly (1). Apply Tooling (B) to the threads of clamp assembly (1). Tighten clamp assembly (1) to a torque of 50 2.5 N m (37 2 lb ft). Do not use power tools in order to tighten clamp assembly (1).
Illustration 3 g02303953
Illustration 4 g02303939
Verify that the cup of the ball joint (G) does not touch the radius of the ball (F). Position ball clamp (7) and hand tighten ball clamp (7). Ball Clamp (7) should be in the center of the joint. Dimension (C) and Dimension (D) should be equal within 2 mm (0.08 inch). Repeat the measurements every 90° around ball clamp (7). If necessary, adjust ball clamp (7). Do not use power tools in order to torque clamp assembly (7). Torque ball clamp (7) to a torque of 35 2 N m (26 1 lb ft).
Illustration 5 g02303555
Typical Example
Note: Ensure that clamp assembly (2) is centered in the cradle pin joint. Align the clamp assembly uniformly over the diesel oxidation catalyst prior to the tightening of the clamp assembly.
Apply Tooling (B) to the threads of clamp assembly (2) for a Distance (X). Distance (X) is 25 mm (1 inch) above the trunnion. Use hand tools in order to tighten clamp assembly (2). Tighten clamp assembly (2) to a torque of 16.5 1.5 N m (146 13 lb in).
Apply Tooling (B) to temperature sensor (6). Tighten temperature sensor (6) to a torque of 45 5 N m (33 4 lb ft).
Connect the cable assembly (not shown) to soot antennae (4) and hand tighten the cable assembly.
Caterpillar SIS machinery equipment:
Caterpillar SIS
390F OEM PT700001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
390D L Excavator WAG00001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
390D L Excavator WBT00001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
390D L Excavator WAP00001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
390D Excavator BYP00001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
390D Excavator KCZ00001-UP (MACHINE) POWERED BY C18 Engine »
363-1685
CYLINDER GP-STICK
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
2811640
CYLINDER HEAD AS
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
3629780
CYLINDER GP-BOOM
390F L
390F L
3624589
CYLINDER GP-BUCKET
390F L
390F L
2635055
CYLINDER HEAD GP
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
24M, 3406E, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B...
1690776
CYLINDER GP-COUPLER
365C, 365C L, 374D L, 374F L, 390D, 390D L, 390F L, CW-10
365C, 365C L, 374D L, 374F L, 390D, 390D L, 390F L, CW-10
7N0296
CYLINDER AS-ETHER
120G, 120H, 120H ES, 120H NA, 120M 2, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 16M, 205B...
120G, 120H, 120H ES, 120H NA, 120M 2, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 16M, 205B...
3571315
CYLINDER BLOCK AS
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G...
3539617
CYLINDER AS
312D2, 385C L, 390D, 390D L, 390F L
312D2, 385C L, 390D, 390D L, 390F L
1884224
CYLINDER AS
385B, 385C, 385C L, 390D, 390D L, 390F L
385B, 385C, 385C L, 390D, 390D L, 390F L
3624928
CYLINDER AS-HYDRAULIC
374F L, 390F L
374F L, 390F L
9T0735
CYLINDER GP-TILT
426, 428
426, 428
2037756
CYLINDER GP-TILT
TH350B, TH355B
TH350B, TH355B
9T0527
CYLINDER GP-STABILIZER
428, 438
428, 438
2956951
CYLINDER GP-LIFT
236B, 236B3
236B, 236B3
4T5601
CYLINDER GP-BUCKET
416, 426, 428
416, 426, 428
2493642
CYLINDER GP-BOOM
TH210, TH215
TH210, TH215
2126179
CYLINDER & MTG GP-FRAME LEVEL
TH460B, TH560B
TH460B, TH560B
8U6174
CYLINDER GP-FOREBOOM
205B, 206B
205B, 206B
1511335
CYLINDER HEAD AS
G3412
G3412
2413159
CYLINDER GP-TELESCOPING
TH350B, TH355B
TH350B, TH355B