AVSPARE.COM
parts catalog

CYLINDER GP-LIFT 3826076 - Caterpillar


3826076 CYLINDER GP-LIFT Caterpillar parts 980M
Rating:
84
Alternative (cross code) number:
CA3826076
382-6076
3826076
Caterpillar 3826076 CYLINDER GP-LIFT
Weight: 571 pounds 259 kg.

Buy CYLINDER GP-LIFT 3826076 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3826076:

WHEEL LOADER  980M   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:

(1) Maximum length of alignment dowel out of crankshaft face (rear dowel) ... 8.4 mm (.33 in)(2) Thickness of thrust plates, at center main bearing ... 5.74 0.04 mm (.226 .002 in)(3) Endplay for the crankshaft (new) ... 0.13 to 0.50 mm (.005 to .020 in)(4) Minimum torque for five plugs ... 23 N m (17 lb ft)"Stake" (make a mark with a punch) the crankshaft to hold the plug tight.(5) Length of dowel out of the crankshaft (front dowel) ... 4.1 0.5 mm (.16 .02 in)(6) Rear seal group. Not to be used if seal and sleeve are separated. Install the seal group in the flywheel housing with the seal positioned as shown. See Special Instruction SMHS8008. Check installations as follows: Arrow on seal ... counterclockwiseDistance from rear face of crankshaft to sleeve - Dimension A ... 1.5 0.5 mm (.06 .02 in)Distance from edge of sleeve to seal - Dimension B ... 6.1 0.6 mm (.24 .02 in) Same procedure and dimensions apply to a crankshaft with a rear gear group.(7) Maximum permissible temperature of the gear for installation on the crankshaft ... 205 °C (401 °F) Install gear with "V" mark to the outside.(8) Make reference to Connecting Rod Bearings.(9) Make reference to Main Bearings.(10) Front seal group. Not to be used if seal and sleeve are separated. Install the seal group in the front accessory drive housing with the seal positioned as shown. See Special Instruction SMHS8008. Check installation as follows: Arrow on seal ... clockwiseSleeve to be flush with front face of crankshaft within ... 0.13 mm (.005 in)Distance from edge of sleeve to seal - Dimension C ... 4.9 0.6 mm (.19 .02 in)

Caterpillar parts catalog:

Caterpillar parts catalog
980M Wheel Loader WW300001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MK200001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MGD00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader XDJ00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader KRS00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader N8T00001-UP (MACHINE) POWERED BY C13 Engine
980L Wheel Loader D8Z00001-UP (MACHINE) POWERED BY C13 Engine


Parts cylinder Caterpillar catalog:

3614768 CYLINDER BLOCK AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621K, 623K, 627K, 730C, 980M, 982M, C13
3614767 CYLINDER BLOCK AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621K, 623K, 627K, 730C, 980M, 982M, C13
3311981 CYLINDER HEAD AS
16M, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 627H, 627K, 730C, 980K, 980K HLG, 980M, 982M, C13, CX31-C13I
3614766 CYLINDER BLOCK AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621K, 623K, 627K, 730C, 980M, 982M, C13
3615592 CYLINDER BLOCK GP
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621K, 623K, 627K, 730C, 980M, 982M, C13
3884770 CYLINDER GP-STEERING
966M, 966M XE, 972M, 972M XE
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.