AVSPARE.COM
parts catalog

CYLINDER & MTG GP-AUGER 3967149 - Caterpillar



3967149 CYLINDER & MTG GP-AUGER Caterpillar parts CYLINDER
Rating:
41
Alternative (cross code) number:
CA3967149
396-7149
3967149
Caterpillar 3967149 CYLINDER & MTG GP-AUGER

Buy CYLINDER & MTG GP-AUGER 3967149 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:


Bench the Grade Control sensors. Press and hold the "bench" function for 3 seconds. Target value will be set to measured value.Note: The grade indicators should indicate "On Grade" or green. Refer to Illustration 3.
Illustration 4 g03821511
Enable the automatic controls.Note: Selecting the automatic mode will highlight the automatic symbol in blue. "AUTO" will be displayed in green. Refer to Illustration 4.During a Run
Once you have completed all the tasks in the "Before a Run" section, you are ready to pull off the starter boards and begin your paving run.Common tasks that you may need to perform during a paving run:
Check Depth.
Check the depth of the mat for correct thickness.
Use arrow keys to adjust for the correct thickness.
Edit target value to match actual depth.
Check Slope.
Check the slope of the mat.
Use arrow keys to adjust if needed.
Edit target slope to calibrate slope sensor.
Check Performance.
Table 1
Status Indication Status Solutions
External Light Bars:
Green "On Grade" LED stays illuminated most of the time with the amber LED above and below the green LED flashing for periods less than one second.
Vertical Graph Bars:
Green upper and lower "On Grade" bars illuminated most of the time with green or red upper or lower bar flashing for periods less than one second. Normal Operation Normal Operation
External Light Bars:
Green "On Grade" indicator stays illuminated for long periods of time
Vertical Graph Bars:
Upper and lower "On Grade" bars illuminated for long periods of time. Normal Operation "ON-Grade" deadband may be set to high(1)
External Light Bars:
Amber LED above or below Green LED is illuminated for long periods of time
Vertical Graph Bars:
Upper or lower graph bars, red, or green, are illuminated for long periods of time. Slow or No Response Condition Elevation:
Check the position of the elevation sensor in relation to the tow point arm(2)
Slope:
Check slope mounting beam for binding or obstructions. (3)
External Light Bars:
Amber LED above and below Green LED are alternating flashing while Green LED is illuminated for short periods of time
Vertical Graph Bars:
Upper or lower graph bars, red or green, are alternating and upper/lower green "On Grade" is illuminated for short periods of time. Fast response/ over-correction Elevation:
Check the position of the elevation sensor in relation to the tow point arm (4)
Slope:
Decrease valve speed (5)
(1) If the grade /slope conditions are changing but not being detected by the system.
(2) Sensor closer to tow point cylinder = faster response. Increase valve speed for elevation.
(3) Increase valve speed for slope.
(4) Sensor further from tow point cylinder = slower response. Decrease valve speed for elevation. "On Grade" dead bands may be set to low
(5) Dead bands for slope may be set too low.Switching Sensors
Cat Grade Control System allows for switching of sensors while maintaining "AUTO" operation. Some jobs require switching from the averaging ski to joint matching with a single sensor. Some jobs also require the switching between grade and slope during operation. Perform the following steps to swap sensors:
Continue paving in "Automatic" control mode.
Touch sensor icon desired to change.
Touch the desired sensor icon to select sensor and press the "OK" softkey on the right side of the screen.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
AP1055 F Asphalt Paver TJ500001-UP (MACHINE) POWERED BY C7.1 Engine
AP1000 F Asphalt Paver AC400001-UP (MACHINE) POWERED BY C7.1 Engine
AP1055 F Asphalt Paver RLM00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts cylinder Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.