CYLINDER BLOCK GP 4786288 - Caterpillar

Earthmoving and engine Dealer Suggested Customer Suggested
Parts Labor Hrs. Parts Labor Hrs. Parts Labor Hrs.
100% 1 0 0 0 0
This is a 1-hour job. U.S. and Canadian Dealers Only - Eligibledealers may enter a Type 2 SIMS ReportPARTS DISPOSITION
The incorrect PIN Plates should be destroyed,by cutting through the bar code and PIN number on the face of the PIN Plate.The cut up plates can then be disposed of.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAMAS SOON AS POSSIBLE.
Attach. (1-Owner Notification)
(2-Rework Procedure)COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS
XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999PRIORITY - Install New Product IdentificationNumber Plates And Stamp FramesMODELS INVOLVED - 545 Wheel Skidders, 990 WheelLoaders, D10R Tractors, CH35, CH45, CH55 Tractors, 570 and 580 Harvestersand 574 ForwardersDear Caterpillar Product Owner:On March 1, 2001, Caterpillar implemented thenew 17 character Product Identification Number (PIN) specified in ISO 10261.New Product Identification Number (PIN) Plates need to be installed oncertain 545 Wheel Skidders, 990 Wheel Loaders, D10R Tractors, CH35, CH45,CH55 Tractors, 570 and 580 Harvesters and 574 Forwarders. The frame-stampedPIN numbers (primary and concealed) also need to be corrected. The correctPIN Plate need to be installed and the frame-stamped PIN corrected on theproducts listed below.Contact your local Caterpillar dealer immediatelyto schedule this service. The dealer will advise you of the time requiredto complete this service. Please refer the dealer to their Service Letterdated July 10, 2001 when scheduling this service. You will not be chargedfor the service performed.We regret the inconvenience this may causeyou, but urge you to have this service performed as soon as possible toprevent unscheduled downtime.
Caterpillar Inc.
Identification #(s)
Attached to July 10, 2001 Service LetterRework ProcedureReplacement Machine Plate Ordering Process
Following is the ordering process for dealersto order replacement machine plates.
Place an order for appropriate replacement machineplate part number, either in ANTARES or Dealer Business System (DBS).
If the order is placed directly in ANTARES, dealersmust enter the required replacement machine plate information in the specialinstruction fields. See Step 2 for the required replacement machine plateinformation.
If the order is placed directly in DBS, dealersmust send the required replacement machine plate information in an emailto Randy Warner, Corporate Security. The email to Randy, the dealer shouldreference the PSO# of the replacement machine plate order. See Step 2 forthe required replacement machine plate information.
Following is required replacement machine plateinformation that must be entered in the Special Instructions field on ANTARESorders or sent via email to Randy Warner, Corporate Security.
For the 9X1878 PIN PlateRequired InformationModel Number:
Product Identification Number:
"Made In" Country IndicatorFor the 1940856 Combination (COMBO) PINPlateRequired InformationModel Number:
Product Identification Number:
"Made In" Country Indicator
Engine Model Number:
Engine Serial Number:
Engine Arrangement Number:
Transmission Model Number:
Transmission Serial Number:
Transmission Arrangement Number:Removing and replacing the PIN PlateThe PIN Plate is held to the frame structurewith 4 aluminum rivets and an adhesive backing. Either pull the rivet outof the frame structure or Cut the rivets with a hacksaw blade or otherserrated edge. Use a putty knife or other sharp edged tool to remove theplate from the product structure.Use a 2-mm drill bit to remove the remainderof the aluminum rivet from the frame holes. Clean the frame surface. Removethe paper backing from