CYLINDER AS 4I1620 - Caterpillar

4I1620 CYLINDER AS Caterpillar parts 320 L, 320N, 325, 325 L, 325 LN, 330, 330 FM L, 350, 350 L, 5080

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4I1620
4I-1620
4I1620

Weight: 185 pounds 83 kg.

Buy CYLINDER AS 4I1620 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, FRONT SHOVEL,

This part in 1 request: Show. This information for suppliers only!

#310737 4I1620

2019-05-15

Compatible equipment models: 4I1620:

EXCAVATOR 320 L 320N 325 325 L 325 LN 330 330 FM L 350 350 L

FRONT SHOVEL 5080 Caterpillar

Number on catalog scheme: 1

Caterpillar 4I1620 Parts scheme CYLINDER AS

For full view, you need register

Information:

Which Generate This Code:This diagnostic code is associated with the circle right solenoid. The FMI 13 diagnostic code is activated when the Implement ECM 2 detects a solenoid that needs calibration. The Implement ECM 2 communicates this condition to the Implement ECM over the J1939 data link and the Implement ECM will activate this diagnostic code.The Implement ECM 2 provides a PWM signal to the solenoid in order to provide proportional control of the solenoid. The electrical current of the PWM signal is varied by the ECM, based on the input command that is received from the position sensor of the circle drive. The sensor is located in the assembly of the right joystick.Note: Before performing this procedure, verify that no other active CID 2168 diagnostic codes exist for the solenoid. If any other diagnostic codes are active for the solenoid, correct the problem before performing this procedure. Test Step 1. CALIBRATION
Perform the calibration procedure for the solenoid. Refer to the Testing and Adjusting, "Calibration" Story in this manual for the correct calibration procedure.Expected Result:The calibration procedure was performed successfully.Results:
OK - The calibration procedure was performed successfully. Resume normal machine operation.STOP
NOT OK - The calibration was not successful.Repair: Repeat the calibration procedure for the solenoid. If the second calibration procedure is not successful, replace the solenoid. After solenoid replacement, refer to the Testing and Adjusting, "Calibration" Story in this manual for the correct calibration procedure. If the problem is still present after replacement and calibration of the new solenoid, the ECM may have failed.Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the cause of the diagnostic code is not found, replace the Implement ECM 2. Refer to the Testing and Adjusting, "Electronic Control Module (ECM) - Replace" Story in this manual for additional information.STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

350 L Excavator Custom Attachments 9FL00001-UP (MACHINE)

7Y-5100: CYLINDER GP-BUCKET » SEBF09050064

350 & 350 L Excavators 8HK00001-UP (MACHINE) POWERED BY 3306 Engine

7Y-5100: CYLINDER GP-BUCKET » SEBP22600420

330, 330L Excavators 2ZM00001-UP (MACHINE)

7Y-5100: CYLINDER GP-BUCKET » SEBP22920339

Parts cylinder Caterpillar catalog:

7Y4906 CYLINDER GP
330, 330 FM L, 330 L

7Y4926 CYLINDER GP
330, 330 FM L, 330 L, 350 L

7C4006 CYLINDER HEAD AS
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235B, 3306, 3306B, 330B L, 350, 528B, 530B, 815B, 966F, 966F II, 966G, 970F, 972G, 973...

1225077 CYLINDER
315B FM L, 317B LN, 318B, 320 L, 320N, OEMS

7Y1866 CYLINDER
1290T, 1390, 2491, 2590, 325D FM, 325D FM LL, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345B, 345B II, 345B II MH, 345B L, 345C...

1028112 CYLINDER
1090, 1190, 1190T, 1390, 2290, 2390, 2391, 320 L, 320B, 320B FM LL, 322B L, 322C, 324D FM, 325, 325 L, 325B, 325B L, 511, 521, 522, OEMS, TK711, TK721, TK722, TK741