AVSPARE.COM
parts catalog

CYLINDER GP-TILT 4Z6413 - Caterpillar



4Z6413 CYLINDER GP-TILT Caterpillar parts D11R CYLINDER
Rating:
9
Alternative (cross code) number:
CA4Z6413
4Z-6413
4Z6413
Caterpillar 4Z6413 CYLINDER GP-TILT
Weight: 983 pounds 445 kg.
Information:
BORE DIAMETER  196.85  mm
CLOSED LENGTH  2052  mm
PIN SIZE CAP END  88.9  mm
PIN SIZE ROD EYE  88.9  mm
ROD DIAMETER  107.95  mm
STROKE  1257 
TYPE  BOLTED HEAD 

Buy CYLINDER GP-TILT 4Z6413 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z6413:

TRACK-TYPE TRACTOR  D11R   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Table 1
Diagnostic Trouble Codes for the Electrical Power Supply Circuit
J1939 Code Code Description Notes
168-3 Battery Potential / Power Input 1 : Voltage Above Normal This code indicates that the battery circuit to the ECM has excessive voltage while the engine is running.
The ECM detects the following conditions:
The battery voltage is high for at least 5 seconds.
The keyswitch is in the ON position.
The engine is not cranking.
The warning lamp will come on.
168-4 Battery Potential / Power Input 1 : Voltage Below Normal This code indicates that the battery circuit for the ECM has low voltage while the engine is running.
The ECM detects the following conditions:
The battery voltage is low for at least 5 seconds.
The keyswitch is in the ON position.
The engine is not cranking.
The ECM will normally log the diagnostic code. If battery voltage disappears without returning, the ECM will not log this diagnostic code and the engine will shut down.
The engine may experience changes in the engine rpm, and intermittent engine shutdowns or complete engine shutdowns while the conditions that cause this diagnostic code are present. Battery+ voltage is supplied through P1: 1, 3, and 5. The battery- is supplied through P1: 2, 4, and 6. The ECM receives the keyswitch signal at P1:54 when the keyswitch is in the ON position or in the START position. When the ECM detects battery voltage at this input, the ECM will activate the main relay. When battery voltage is removed from this input, after a short time (up to 60 seconds) the ECM will deactivate the main relay.The cause of an intermittent power supply to the ECM can occur on either the positive side or on the negative side of the battery supply circuit.Usually, battery power to the diagnostic connector is available and the battery power to the data link connector is independent of the keyswitch. Therefore, although the electronic service tool can be powered up, there may be no communication with the engine ECM. The engine ECM requires the keyswitch to be in the ON position in order to maintain communications. The ECM may power down a short time after connecting the electronic service tool if the keyswitch is in the OFF position.
Illustration 1 g03722958
Schematic diagram for the electrical power supply circuit
Not all connectors are shown. Refer to the Electrical Schematic for the application.
Illustration 2 g03722982
View of the pin locations on the P1 connector for the electrical power supply circuit
(1) Battery+
(2) Battery ground
(3) Battery+
(4) Battery ground
(5) Battery+
(6) Battery ground
(8) Start Signal
(28) ECM main relay
(54) Ignition key switch
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Check the fuses.
B. Thoroughly inspect the battery connections and the connections to the relays. Refer to Troubleshooting, "Electrical Connector - Inspect" for details.
C. Perform a 30 N (6.7 lb) pull test on each of the wires in the ECM connector that are associated with electrical power supply circuit.
D. Check the harness for abrasion and for pinch points from the battery to the ECM.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D11R Track-Type Tractor 9TR00001-UP (MACHINE) POWERED BY 3508 Engine


Parts cylinder Caterpillar catalog:

3172440 CYLINDER HEAD GP
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H,...
6E3113 CYLINDER GP-RIPPER PIN PULLER
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
2425328 CYLINDER HEAD AS
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H...
3504386 CYLINDER HEAD GP
3516B, 5130B, 5230B, 776D, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H, D11N, D11R
2014257 CYLINDER HEAD GP
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 789C, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, D11R, PM3508, PM3512, PM3516, PP3516, ...
3492859 CYLINDER BLOCK GP
777C, 777D, 777F, 777G, 854K, 992K, 993K, C32, D11R, D11T
6E6175 CYLINDER
416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 725, 730, 769D, 771D, 773D, 775D, 844, 990, 990 II, D11R, D250E II, D300E II, TH103, TH48-E70
6E3264 CYLINDER
416C, 416D, 420D, 426C, 430D, 436C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K...
7X1062 CYLINDER AS-ETHER
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
6E3976 CYLINDER AS
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.