5T6617 CYLINDER A- Caterpillar parts
Rating:
Alternative (cross code) number:
CA5T6617
5T-6617
5T6617
CA5T6617
5T-6617
5T6617
Weight: 3 pounds 1 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$65.71
14 Sep 2023
Amazon.com
CTP 5T6617 Cylinder for Braking System
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
$64.17
15 Jul 2023
Amazon.com
CTP 5T6617 Cylinder for Braking System
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
$60.56
16 Jun 2023
Amazon.com
CTP 5T6617 Cylinder for Braking System
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP For CTP Braking System || Highly Efficient || Easy in-and-out fit
For full view, you need register
Information:
Removal Procedure
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
The bellows assembly must be supported always when the bellows assembly is not installed in the application. Failure to support the bellows assembly adequately could result in the failure of the bellows assembly. Do not use power tools to disassemble or assemble any part of the flexible exhaust system.The alignment of the bellows assembly is important. Incorrect alignment may lead to premature failure of the bellows assembly. Misalignment can be identified by visually inspecting the uniformity of the spacing between the convolutions on the bellows assembly.Inspect the bellows assembly for damage prior to installation. If there is any damage to the convolutions, discard the bellows assembly. If there is any difficulty in installation after the repair, discard the bellows assembly.
Illustration 1 g06306309
Disconnect spring assemblies (2) and (4).
Remove heat shields (1) and (3).
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Illustration 2 g06196364
Illustration 3 g06207955Note: Ball clamps (7) and (10) are designed for one time use.
Use two people to remove exhaust line (8). The weight of exhaust line (8) is approximately 40 kg (89 lb).
Remove nuts (6) and brackets (9).
Remove ball clamps (7).
Remove exhaust line (8) with slip tube (12), clamp (11), clamp (10), and elbow (5) as a unit.
Illustration 4 g06196363Note: Ball clamps (17) and (18) are designed for one time use.
Use two people to remove exhaust line (13). The weight of exhaust line (13) is approximately 30 kg (67 lb).
Remove nuts (16) and brackets (15).
Remove ball clamps (17).
Remove exhaust line (13) with elbow (14) and clamp (18) as a unit.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize -
B - Digital Protractor 1
Illustration 5 g06194488
Install exhaust elbow (5), plates (9), and nuts (6). Loosely tighten nuts (6).
Install exhaust elbow (14), plates (15), and nuts (16). Loosely tighten nuts (16).
Illustration 6 g06193811
Illustration 7 g06195318
Pre assemble slip tube (12) to the bellows assembly of exhaust line (8).
The slip joint at clamp (11) and slip tube (12) should overlap by a minimum length of 40 mm (1.6 inch). The engagement is sufficient when the ink line on slip tube (12) is no longer visible.
Illustration 8 g06193699
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
The bellows assembly must be supported always when the bellows assembly is not installed in the application. Failure to support the bellows assembly adequately could result in the failure of the bellows assembly. Do not use power tools to disassemble or assemble any part of the flexible exhaust system.The alignment of the bellows assembly is important. Incorrect alignment may lead to premature failure of the bellows assembly. Misalignment can be identified by visually inspecting the uniformity of the spacing between the convolutions on the bellows assembly.Inspect the bellows assembly for damage prior to installation. If there is any damage to the convolutions, discard the bellows assembly. If there is any difficulty in installation after the repair, discard the bellows assembly.
Illustration 1 g06306309
Disconnect spring assemblies (2) and (4).
Remove heat shields (1) and (3).
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Illustration 2 g06196364
Illustration 3 g06207955Note: Ball clamps (7) and (10) are designed for one time use.
Use two people to remove exhaust line (8). The weight of exhaust line (8) is approximately 40 kg (89 lb).
Remove nuts (6) and brackets (9).
Remove ball clamps (7).
Remove exhaust line (8) with slip tube (12), clamp (11), clamp (10), and elbow (5) as a unit.
Illustration 4 g06196363Note: Ball clamps (17) and (18) are designed for one time use.
Use two people to remove exhaust line (13). The weight of exhaust line (13) is approximately 30 kg (67 lb).
Remove nuts (16) and brackets (15).
Remove ball clamps (17).
Remove exhaust line (13) with elbow (14) and clamp (18) as a unit.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize -
B - Digital Protractor 1
Illustration 5 g06194488
Install exhaust elbow (5), plates (9), and nuts (6). Loosely tighten nuts (6).
Install exhaust elbow (14), plates (15), and nuts (16). Loosely tighten nuts (16).
Illustration 6 g06193811
Illustration 7 g06195318
Pre assemble slip tube (12) to the bellows assembly of exhaust line (8).
The slip joint at clamp (11) and slip tube (12) should overlap by a minimum length of 40 mm (1.6 inch). The engagement is sufficient when the ink line on slip tube (12) is no longer visible.
Illustration 8 g06193699
Parts cylinder Caterpillar catalog:
Caterpillar
Caterpillar
Caterpillar
5T6531
CYLINDER KIT-
Caterpillar
Caterpillar
Caterpillar
Caterpillar
5U2360
CYLINDER A
Caterpillar
Caterpillar
5U0682
CYLINDER GP-
Caterpillar
Caterpillar
5T8956
CYLINDER
Caterpillar
Caterpillar
Caterpillar
5T7159
CYLINDER KIT-
Caterpillar
Caterpillar
Caterpillar