AVSPARE.COM
parts catalog

CYLINDER AS 6E3296 - Caterpillar


6E3296 CYLINDER AS Caterpillar parts 436
Rating:
53
Alternative (cross code) number:
CA6E3296
6E-3296
6E3296
Caterpillar 6E3296 CYLINDER AS
Weight: 0.23 pounds 0 kg.

Buy CYLINDER AS 6E3296 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compatible equipment models: 6E3296:

BACKHOE LOADER  436   Caterpillar
Number on catalog scheme: 1
  For full view, you need register

Information:


Move the bucket tilt lever to the TILT BACK detent position.
Before you lower the bucket, make sure that the hauling unit is not under the bucket.
Lower the bucket while you position the loader for the next load.Loading with a Bucket from a Bank
Personal injury or death can result from falling material.Remove any overhang and watch for sliding material.
Illustration 5 g00101771
Start at the base of the bank in order to load the bucket and follow the face upward.
Raise the bucket slightly and move away from the bank.Multipurpose Bucket Operation
Loading with a Bucket
Illustration 6 g00104393
Open the bowl and position the bucket over the material that will be loaded. Lower the bucket and close the bowl.
Illustration 7 g00104391
The multipurpose bucket can be used when increased dump height is desired or when you are unloading sticky material. Position the bucket over the dump area and open the bowl.Dozing
Illustration 8 g00104392
To use the bucket for dozing, open the bowl. Maintain a level cut.Scraping
Illustration 9 g00104392
To use the bucket for scraping, raise the bowl slightly and position the bucket as if the bucket is used for dozing. When the bucket is loaded, tilt back the bucket and close the bowl. The bucket is dumped in the normal tilt forward position.Pallet Forks
Illustration 10 g00104348
Slowly, move the machine into position and engage the load. The machine should be square with the load. Space the forks as far as possible from each other.
Move the machine forward until the load touches the carriage.
Push the kickout control to the OFF position in order to disable the lever detents. This will prevent the lever from being pulled into the DETENT position when you are handling delicate loads.
Lift the load carefully.
Operate the machine in reverse until the load is clear enough to lower.
Lower the load to the travel position.Travel with the load as low as possible while you still maintain ground clearance.Travel with the load uphill on upgrades and on downgrades.For better visibility, travel in reverse with bulky loads.Logging Fork Clamp
Illustration 11 g00291587
Open the top clamp. Position the fork in the center of the load.
Close the top clamp. Tilt the forks backward in order to hold the load against the uprights on the forks.
For the best operator vision and stability for the loader, carry the load as low as possible to the ground.
Illustration 12 g00100578
Position the load over the loading area. Tilt the fork downward and raise the clamp in order to release the load.Material Handling Arm
Illustration 13 g03394737
Remove the retainer pins from the arm in order to extend the arm or retract the arm.To lock the arm into position, replace the retainer pins after the arm has been extended or retracted.Push the kickout control to the OFF position in order to disable the lever detents. This will prevent the lever from being pulled into the DETENT position when you are handling delicate loads.Lift the load close to the machine for best stability. Move the machine slowly in order to avoid excessive load swing.Do not apply side loads on the hook and on the shackle. Check the condition of the

Caterpillar parts catalog:

Caterpillar parts catalog
436 SERIES II BACKHOE LOADER 5KF00806-UP (MACHINE) POWERED BY 4.236 DIESEL ENGINE


Parts cylinder Caterpillar catalog:

9T4006 CYLINDER GP-BUCKET
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 432D, 432E, 434E, 436, 436B, 436C, 438, 438B, 438C, 442D, 442E, 444E, 902, 906, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH62, TH63, T...
9T1493 CYLINDER GP-STEERING
416, 426, 428, 436, 438
6E0113 CYLINDER GP-TILT
426, 426B, 426C, 428, 428B, 428C, 436, 436B, 436C, 438, 438B, 438C
7C6070 CYLINDER BLOCK AS
416, 426, 428, 436, 438
6E5190 CYLINDER GP-STEERING
416, 416B, 426, 426B, 428B, 436, 436B
4P4722 CYLINDER HEAD GP
206, 416, 428, 436, CB-424, CS-323, PR-75
6E0097 CYLINDER GP-STABILIZER-LH
416, 416B, 426, 426B, 436, 436B
7T3172 CYLINDER
416, 416B, 426B, 428, 428B, 436
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.