7J9691 CYLINDER ASSEM. Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA7J9691
7J-9691
7J9691
CA7J9691
7J-9691
7J9691
Weight: 124 pounds 56 kg.
Information:
BEARING TYPE
SLEEVE
BORE DIAMETER
139.75
mm
GREASE PORT
N
MOUNT TYPE
TRUNNION
TYPE
3
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 7J9691 Hydraulic Cylinder for Model 950
CTP For Model 950 || Sold in each || Easy in-and-out fit
CTP For Model 950 || Sold in each || Easy in-and-out fit
CTP 7J9691 Hydraulic Cylinder for Model 950
CTP For Model 950 || Sold in each || Easy in-and-out fit
CTP For Model 950 || Sold in each || Easy in-and-out fit
Compatible equipment models: 7J9691:
Information:
Emergency shutoff controls are for EMERGENCY use ONLY. DO NOT use emergency shutoff devices or controls for normal stopping procedure.
Ensure that any components for the external system that aid the engine operation are secured after the engine is stopped.Emergency Stop Button
Use of the emergency stop will shut off the fuel. If the engine is equipped with air shutoffs, the air shutoffs will also be activated. Refer to "Air Shutoffs (if equipped)" in this section. For operation of the emergency stop button, see the instructions that are provided by the OEM of the equipment.
Do not start the engine until the problem necessitating the emergency stop has been located and corrected.
If the emergency stop button was pushed in order to shut down the engine, it will be necessary to reset the emergency stop button before restarting the engine.If the emergency stop button is used, both of the air shutoffs must be reset before the engine can be restarted.The power for the ECM must be cycled before the engine can be restarted.Air Shutoffs (If Equipped)
Illustration 1 g00669239
Earlier ModelsReset knob for the air shutoff
Illustration 2 g01164039
Later ModelsReset hex for the air shutoffThe air shutoffs are activated by oil pressure when energy to a solenoid is interrupted or a solenoid that is mounted on the shutoff is electrically activated. Earlier models use a plate that rotates on a shaft in order to shut off inlet air to the aftercooler. Later models use a plate that slides when the mechanism is activated in order to shut off inlet air to the aftercooler. The engine stops because of the restricted air supply to the combustion chamber. The air shutoffs will actuate for the following conditions:Note: A switch may be supplied by the customer in order to activate the air shutoffs.
The emergency stop button is pressed.
The air shutoff is activated.
An overspeed condition occurs.
The electronic control module loses power.The air shutoffs must be manually reset before the engine is restarted. To reset the air shutoffs, turn the knob or the hex until the air shutoff is in the "OPEN" position. Ensure that both of the air shutoffs are reset.Power to the ECM must be cycled in order to restart the engine. Turn the battery disconnect switch to the OFF position for three seconds. Turn the battery disconnect switch back to the ON position. The engine may now be restarted.
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
7N6552
CYLINDER BLOCK AS
120G, 130G, 215, 215B, 215C, 215D, 219D, 225, 225D, 229, 229D, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 920, 930, 930R, 936, 936F, 941, 950, 950B, 950B/950E, 951B, 955L, 963, CB-534, CS-643, D4E, D...
120G, 130G, 215, 215B, 215C, 215D, 219D, 225, 225D, 229, 229D, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 920, 930, 930R, 936, 936F, 941, 950, 950B, 950B/950E, 951B, 955L, 963, CB-534, CS-643, D4E, D...
1N3574
CYLINDER BLOCK GP
120G, 130G, 215, 215B, 215C, 215D, 219D, 225, 225D, 229, 229D, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 920, 930, 930R, 936, 936F, 941, 950, 950B, 950B/950E, 951B, 955L, 963, CB-534, D4E, D4E SR, D...
120G, 130G, 215, 215B, 215C, 215D, 219D, 225, 225D, 229, 229D, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 920, 930, 930R, 936, 936F, 941, 950, 950B, 950B/950E, 951B, 955L, 963, CB-534, D4E, D4E SR, D...
4V5414
CYLINDER GP-AIR OVER HYD
518, 528, 528B, 530B, 930, 930R, 950, FB518
518, 528, 528B, 530B, 930, 930R, 950, FB518
5V4003
CYLINDER AS-MASTER
950, 966C, 966R
950, 966C, 966R
8N1188
CYLINDER HEAD GP
120G, 130G, 215, 225, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E
120G, 130G, 215, 225, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E
5V4004
CYLINDER AS
950, 966C, 966R
950, 966C, 966R
7S7070
CYLINDER HEAD AS
3304, 941, 950, D4D
3304, 941, 950, D4D
9K1591
CYLINDER ASSEM.
518, 528, 528B, 530B, 920, 930, 950
518, 528, 528B, 530B, 920, 930, 950
5K7154
CYLINDER ASSEM.
930, 950
930, 950
2V6811
CYLINDER KIT
930, 950
930, 950
6J4520
CYLINDER ASSEM.
980, 980B
980, 980B
3J6659
CYLINDER ASSEM.
834, 988
834, 988
5J0181
CYLINDER ASSEM.
12E, 14G, 16G
12E, 14G, 16G