7J9839 CYLINDER AS-HYDRAULIC Caterpillar parts
920, 930R
Rating:
Alternative (cross code) number:
CA7J9839
7J-9839
7J9839
CA7J9839
7J-9839
7J9839
Weight: 33 pounds 14 kg.
Information:
BEARING TYPE
SLEEVE
BORE DIAMETER
76.25
mm
GREASE PORT
N
MOUNT TYPE
EYE
TYPE
3
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 7J9839 Hydraulic Cylinder for Model 920/930R
CTP For Model 920/930R || Sold in each || Easy in-and-out fit
CTP For Model 920/930R || Sold in each || Easy in-and-out fit
CTP 7J9839 Hydraulic Cylinder for Model 920/930R
CTP For Model 920/930R || Sold in each || Easy in-and-out fit
CTP For Model 920/930R || Sold in each || Easy in-and-out fit
Number on catalog scheme:
1
For full view, you need register
Information:
Remove & Install Exhaust Manifold
Start By:a. remove turbochargerb. remove aftercooler 1. Loosen clamp (4). Disconnect hose (3).2. Disconnect fitting (5) at each end and remove tube (7).3. Remove two bolts (8), nuts and washers.4. Reposition temperature gauge (6) out of the way.5. Install Tool (A), chains and a suitable lifting device to exhaust manifold (2) as shown.6. Remove twenty-four bolts (1).7. Remove exhaust manifold (2) and the three gaskets. The following steps are for the installation of the exhaust manifold.8. Check the condition of the three gaskets used between the cylinder head assembly and the exhaust manifold. If the gaskets are worn or damaged, use new parts for replacement.9. Apply 5P3931 Anti-Seize Compound to the threads of bolts (1) that hold the exhaust manifold to the cylinder head assembly.10. Position the three gaskets and exhaust manifold (2) on the cylinder head assembly. Install mounting bolts (1), and tighten them evenly to a torque of 55 10 Nm (41 7 lb ft).End By:a. install aftercoolerb. install turbocharger
Start By:a. remove turbochargerb. remove aftercooler 1. Loosen clamp (4). Disconnect hose (3).2. Disconnect fitting (5) at each end and remove tube (7).3. Remove two bolts (8), nuts and washers.4. Reposition temperature gauge (6) out of the way.5. Install Tool (A), chains and a suitable lifting device to exhaust manifold (2) as shown.6. Remove twenty-four bolts (1).7. Remove exhaust manifold (2) and the three gaskets. The following steps are for the installation of the exhaust manifold.8. Check the condition of the three gaskets used between the cylinder head assembly and the exhaust manifold. If the gaskets are worn or damaged, use new parts for replacement.9. Apply 5P3931 Anti-Seize Compound to the threads of bolts (1) that hold the exhaust manifold to the cylinder head assembly.10. Position the three gaskets and exhaust manifold (2) on the cylinder head assembly. Install mounting bolts (1), and tighten them evenly to a torque of 55 10 Nm (41 7 lb ft).End By:a. install aftercoolerb. install turbocharger
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
120G, 130G, 215, 215B, 215C, 215D, 219D, 225, 225D, 229, 229D, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 920, 930, 930R, 936, 936F, 941, 950, 950B, 950B/950E, 951B, 955L, 963, CB-534, CS-643, D4E, D...
518, 528, 528B, 530B, 930, 930R, 950, FB518
528, 528B, 530B, 920, 930
930, 930R
120G, 130G, 215, 215B, 215C, 225, 229, 3304, 3304B, 515, 517, 518, 518C, 525, 527, 930R, 936, 936F, CS-643, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, E240, FB518, G936
920, 930, 930R
930, 930R
930, 930R
120G, 130G, 215, 225, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E
920, 930, 930R
518, 528, 528B, 530B, 920, 930, 950
930, 930R
9D1359
CYLINDER
637D
637D
8J3543
CYLINDER ASSEM.
633C, 633D
633C, 633D