8D3310 CYLINDER & MOUNTING GP Caterpillar parts
120G, 12G, 130G, 140G, 160G
Rating:
Alternative (cross code) number:
CA8D3310
8D-3310
8D3310
CA8D3310
8D-3310
8D3310
Weight: 0.01 pounds 0 kg.
MOTOR GRADER,
Information:
Illustration 25 g06277746
Example of stud with out markings
Illustration 26 g06277743
Example of stud after stud has been tightened. Marks can be made with an X stamp. Be sure to stay away from thread area when stamping.
3600 and C280 Engine Fasteners
Use the following guidelines to determine the serviceability of the fasteners:Thoroughly inspect the fasteners before you reuse any fastener. Do not reuse a fastener that has any damage. Do not reuse a fastener that has any of these defects:
Rust
Nicks
Thread damage
Cracks
Pits
DeformationIf the fasteners appear to be free of defects, also follow these guidelines:
Replace any stud for the cylinder head after the stud has been tensioned 20 times. This criteria includes the 1W-2363 Taperlock Stud, 7E-8400 Taperlock Stud, and 187-0450 Taperlock Stud.
Also replace any stud for the main bearing cap ( 1W-0121 Taperlock Stud) after the stud has been tensioned 20 times.
The cross tie bolt for the main bearing cap ( 3S-7079 Bolt) can only be tensioned five times.
For the Torque Turn Bolts 1W-0098, 369-7181, and 467-0537, refer to Engine News, SEBD9992, "A New Torque Procedure for Connecting Rod Bolts Is Now Used on 3600, G3600, and C280 Engines".
Inspect connecting rod bolts at each service of the connecting rod bearings. There should be no fretting on the shank, knurled or annular ring area (2) of the connecting rod bolt. Ensure that the connecting rod bolt meets the guidelines for the reusable parts. Do not reuse the connecting rod nuts.
Prior to installation of the new 467-0537 Bolt As, inspect heat shrink tube (1). The tube serves as an alignment sleeve for the bolts.
The heat shrink tube must be firmly in place and must not move under light finger pressure.
The whole surface of the tube must be smooth.
The tube must not extend into the fillet that is under the bolt head.
If a problem is found with the tube, use the following replacement procedure.
Carefully cut the heat shrink tube from the bolt.
Ensure that there is no damage to the shank of the bolt that was under the tube.
Clean the shank of the bolt with solvent to remove any oil.
Install a new 369-7183 Heat Shrink Tube onto the bolt. Position the tube approximately 1.5 mm (0.059 inch) under the bolt head, away from the fillet that is under the bolt head.
Use a heat gun or place the bolt and tube in an oven at 135° 14°C (275° 25°F) for 10 minutes. The tube must shrink into place without any bumps or wrinkles.
After the bolt cools, the tube must be firmly in place. The tube must not move under light finger pressure.
Make sure that the surface of the tube is smooth all around. Verify that the tube does not extend onto the fillet that is under the bolt head.Note: The 467-0537 Bolt As may be tightened for a maximum of five times. The reuse includes retightening after checking the rod bore or bearing clearance. Do not reuse the connecting rod nuts.
An overloaded bolt can be detected by threading a new 205-0640 Nut onto the bolt
Caterpillar SIS machinery equipment:
Caterpillar SIS
120G MOTOR GRADER 11W01019-01250 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 12W00696-01081 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
140G MOTOR GRADER 13W00425-00740 (MACHINE) POWERED BY 3306DI ENGINE »
8D-3310
CYLINDER & MTG GP-STEERING
12G MOTOR GRADER 3WC00001-01066 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
120G MOTOR GRADER 82V00668-UP (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
120G MOTOR GRADER 82V00668-UP (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 74V00588-01656 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 74V00588-01656 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 12W00001-00695 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 12W00001-00695 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
12G MOTOR GRADER 61M02629-07710 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
12G MOTOR GRADER 61M02629-07710 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
12G MOTOR GRADER 61M07711-12026 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MTG GP-STEERING
140G MOTOR GRADER 72V04231-10333 (MACHINE) POWERED BY 3306 ENGINE »
8D-3310
CYLINDER & MTG GP-STEERING
130G MOTOR GRADER 74V01657-02058 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MTG GP-STEERING
120G MOTOR GRADERS 87V05275-08359 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 74V02059-02320 (MACHINE) POWERED BY 3304 ENGINE »
8D-3310
CYLINDER & MOUNTING GP
160G MOTOR GRADER 4JD00001-00140 (MACHINE) POWERED BY 3306DI ENGINE »
8D-3310
CYLINDER & MTG GP-STEERING
130G MOTOR GRADER 7GB01224-UP (MACHINE) »
8D-3310
CYLINDER & MOUNTING GP
12G MOTOR GRADER 61M00001-02628 (MACHINE) »
8D-3310
CYLINDER & MOUNTING GP
140G MOTOR GRADER 72V00001-00822 (MACHINE) »
8D-3310
CYLINDER & MOUNTING GP
130G MOTOR GRADER 74V00001-00587 (MACHINE) »
8D-3310
CYLINDER & MOUNTING GP
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
8J0028
CYLINDER GP-BLADE SIDESHIFT
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3G8070
CYLINDER GP-STEERING
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3G4752
CYLINDER GP-WHEEL LEAN
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3G8069
CYLINDER GP-STEERING
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
8N6796
CYLINDER HEAD GP
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 235, 235B, 235D, 330, 330 FM L, 330 L, 3306, 3306B, 330B, 330B L, 350, 528, 528B, 530B, 545,...
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 235, 235B, 235D, 330, 330 FM L, 330 L, 3306, 3306B, 330B, 330B L, 350, 528, 528B, 530B, 545,...
9J3466
CYLINDER GP-BLADE TIP
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
3G5224
CYLINDER GP-CENTERSHIFT
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
3G5223
CYLINDER GP-BLADE LIFT
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
1052094
CYLINDER GP-SIDESHIFT
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
7C4006
CYLINDER HEAD AS
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235B, 3306, 3306B, 330B L, 350, 528B, 530B, 815B, 966F, 966F II, 966G, 970F, 972G, 973...
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235B, 3306, 3306B, 330B L, 350, 528B, 530B, 815B, 966F, 966F II, 966G, 970F, 972G, 973...
8W0328
CYLINDER-DAMPER
120G, 12G, 130G, 140G, 14G, 160G, 16G, 508
120G, 12G, 130G, 140G, 14G, 160G, 16G, 508
9T2482
CYLINDER AS
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
2912682
CYLINDER GP-STABILIZER
416E, 416F, 420E, 420F, 430E, 430F
416E, 416F, 420E, 420F, 430E, 430F
2742453
CYLINDER GP-STICK
345C, 345D, 345D L, 349D, 349D L
345C, 345D, 345D L, 349D, 349D L
2590850
CYLINDER GP-BOOM
319D, 319D L, 319D LN
319D, 319D L, 319D LN
1515304
CYLINDER HEAD AS
315B, 315C, 317B LN, 318B
315B, 315C, 317B LN, 318B
2667933
CYLINDER & LINES GP-BOOM
328D LCR
328D LCR
1407372
CYLINDER HEAD AS
3116, 938G, 950G, 962G, IT38G, IT62G
3116, 938G, 950G, 962G, IT38G, IT62G
1291150
CYLINDER HEAD GP
3126, 938G, 950G, 962G, IT38G, IT62G
3126, 938G, 950G, 962G, IT38G, IT62G
2426731
CYLINDER & SEAL GP-BOOM
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
4Z6364
CYLINDER GP-RIPPER TIP
D9R, D9T
D9R, D9T
3579783
CYLINDER & SEAL GP-BUCKET
330D L, 336D, 336D L, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D2 L, 345C, 345D, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L
330D L, 336D, 336D L, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D2 L, 345C, 345D, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L