9T0143 CYLINDER GP-RIPPER TILT Caterpillar parts
D8N, D8R
Rating:
Alternative (cross code) number:
CA9T0143
9T-0143
9T0143
CA9T0143
9T-0143
9T0143
Weight: 330 pounds 149 kg.
Information:
BORE DIAMETER
165.1
mm
CLOSED LENGTH
1243
mm
PIN SIZE CAP END
76.2
mm
PIN SIZE ROD EYE
76.2
mm
ROD DIAMETER
76.2
mm
STROKE
437
TYPE
BOLTED HEAD
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$5,434.89
17 Nov 2023
Amazon.com
CTP 9T0143 Ripper Tilt Hydraulic Cylinder Group for Model D8N/D8R
CTP For Model D8N/D8R || Sold in each || Easy in-and-out fit
CTP For Model D8N/D8R || Sold in each || Easy in-and-out fit
$5,201.42
25 Oct 2023
Amazon.com
CTP 9T0143 Ripper Tilt Hydraulic Cylinder Group for Model D8N/D8R
CTP For Model D8N/D8R || Sold in each || Easy in-and-out fit
CTP For Model D8N/D8R || Sold in each || Easy in-and-out fit
Information:
Disassemble Rocker Shaft Assembly
START BY:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove the plugs from each end of the shaft if necessary.Assemble Rocker Shaft Assembly
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on the rocker shaft. Make sure the hole in the rear support bracket is in alignment with the hole in the rocker shaft.3. Put pin (3) in position in the bracket. 4. Install pin (3) through the bracket and shaft with a hammer.5. Pin (3) must extend 9.60 mm (.378 in.) above the bracket. 6. Install O-ring seal (7) in the rear support bracket. Install rocker arm (8), the original number of washers, spring, washer and the retainer ring on the rocker shaft.7. Install the front support, rocker arm, original number of washers, spring, washer and the retainer ring on the rocker shaft.8. Install the plugs in each end of the rocker shaft if they were removed.END BY:a. install rocker shaft assembly and push rods
START BY:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove the plugs from each end of the shaft if necessary.Assemble Rocker Shaft Assembly
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on the rocker shaft. Make sure the hole in the rear support bracket is in alignment with the hole in the rocker shaft.3. Put pin (3) in position in the bracket. 4. Install pin (3) through the bracket and shaft with a hammer.5. Pin (3) must extend 9.60 mm (.378 in.) above the bracket. 6. Install O-ring seal (7) in the rear support bracket. Install rocker arm (8), the original number of washers, spring, washer and the retainer ring on the rocker shaft.7. Install the front support, rocker arm, original number of washers, spring, washer and the retainer ring on the rocker shaft.8. Install the plugs in each end of the rocker shaft if they were removed.END BY:a. install rocker shaft assembly and push rods
Caterpillar SIS machinery equipment:
Caterpillar SIS
D8N TRACTOR 9TC00001-UP (MACHINE) POWERED BY 3406 ENGINE »
9T-0143
CYLINDER GP-RIPPER TILT
D8N TRACTOR 1XJ00001-UP (MACHINE) POWERED BY 3406 ENGINE »
9T-0143
CYLINDER GP-RIPPER TILT
D8N TRACTOR 1XJ00001-UP (MACHINE) POWERED BY 3406 ENGINE »
9T-0143
CYLINDER GP-RIPPER TILT
D8N TRACTOR / POWER SHIFT / 5TJ00001-UP (MACHINE) POWERED BY 3406 ENGINE »
9T-0143
CYLINDER GP-RIPPER TILT
D8N TRACTOR / POWER SHIFT / 5TJ00001-UP (MACHINE) POWERED BY 3406 ENGINE »
9T-0143
CYLINDER GP-RIPPER TILT
D8N Track-Type Tractor 7TK00001-UP (MACHINE) »
9T-0143
CYLINDER GP-TILT
D8R Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine »
9T-0143
CYLINDER GP-TILT
D8R TRACK-TYPE TRACTOR 9EM00001-UP (MACHINE) POWERED BY 3406C Engine »
9T-0143
CYLINDER GP-TILT
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
6E1175
CYLINDER GP-TILT
D8N, D8R, D8R II
D8N, D8R, D8R II
2505861
CYLINDER GP-BULLDOZER LIFT
D8R, D8T
D8R, D8T
2141667
CYLINDER HEAD GP
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
6E1102
CYLINDER GP-BULLDOZER LIFT
D8N, D8R, D8R II
D8N, D8R, D8R II
2407347
CYLINDER GP-TILT
D8R, D8T
D8R, D8T
6E3976
CYLINDER AS
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
7T3697
CYLINDER AS
D8N, D8R
D8N, D8R
6E1176
CYLINDER AS
D8N, D8R, D8R II
D8N, D8R, D8R II
6E1103
CYLINDER AS
D8N, D8R, D8R II
D8N, D8R, D8R II
2388637
CYLINDER AS
D8R, D8T
D8R, D8T
9Y2629
CYLINDER BLOCK GP
212, AP-800, CP-433B, CS-431B, RT50, WE-601B
212, AP-800, CP-433B, CS-431B, RT50, WE-601B
2706933
CYLINDER HEAD GP
3013C, C1.5
3013C, C1.5
0814716
CYLINDER GP-AIR
PS-300, PS-500
PS-300, PS-500
1327901
CYLINDER GP-STICK
330B L, 330C FM, 330D FM
330B L, 330C FM, 330D FM
4172661
CYLINDER GP-BUCKET
330D L, 336D, 336D2, 340D2 L, 345D, 345D L, 349D, 349D L
330D L, 336D, 336D2, 340D2 L, 345D, 345D L, 349D, 349D L
3016878
CYLINDER & LINES GP-BOOM
345D, 345D L, 349D, 349D L
345D, 345D L, 349D, 349D L
2445548
CYLINDER & SEAL GP-TILT
950H, 962H
950H, 962H