9T5218 CYLINDER AS Caterpillar parts
428
Rating:
Alternative (cross code) number:
CA9T5218
9T-5218
9T5218
CA9T5218
9T-5218
9T5218
Weight: 59 pounds 26 kg.
Information:
BORE DIAMETER
82.55
mm
GREASE PORT
N
MOUNT TYPE
EYE
TYPE
1
BACKHOE LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$1,005.85
13 Dec 2022
Amazon.com
CTP 9T5218 Hydraulic Cylinder for Model 428
CTP For Model 428 || Sold in each || Easy in-and-out fit
CTP For Model 428 || Sold in each || Easy in-and-out fit
$1,022.42
22 Oct 2022
Amazon.com
CTP 9T5218 Hydraulic Cylinder for Model 428
CTP For Model 428 || Sold in each || Easy in-and-out fit
CTP For Model 428 || Sold in each || Easy in-and-out fit
$1,036.57
30 Aug 2022
Amazon.com
CTP 9T5218 Hydraulic Cylinder for Model 428
CTP For Model 428 || Sold in each || Easy in-and-out fit
CTP For Model 428 || Sold in each || Easy in-and-out fit
Number on catalog scheme:
14
For full view, you need register
Compatible equipment models: 9T5218:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
178-8615 Engine Turning Tool(1) 1
(1) Can be used to turn the crankshaft from the front of the engine.Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01144041
Use Tooling (A) to rotate the crankshaft to gain access to the piston cooling jet.
Remove bolt (1) and remove piston cooling jet (2).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01144041
Use Tooling (A) to rotate the crankshaft to gain access to the piston cooling jet.Note: Engine damage may occur if the piston cooling jet is not installed properly. Install the piston cooling jet by hand.
Position piston cooling jet (2) in the cylinder block. Ensure that piston cooling jet (2) is flush with the cylinder block. Install bolt (1). Tighten bolt (1) to a torque of 28 7 N m (21 5 lb ft).End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
178-8615 Engine Turning Tool(1) 1
(1) Can be used to turn the crankshaft from the front of the engine.Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01144041
Use Tooling (A) to rotate the crankshaft to gain access to the piston cooling jet.
Remove bolt (1) and remove piston cooling jet (2).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01144041
Use Tooling (A) to rotate the crankshaft to gain access to the piston cooling jet.Note: Engine damage may occur if the piston cooling jet is not installed properly. Install the piston cooling jet by hand.
Position piston cooling jet (2) in the cylinder block. Ensure that piston cooling jet (2) is flush with the cylinder block. Install bolt (1). Tighten bolt (1) to a torque of 28 7 N m (21 5 lb ft).End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 432D, 432E, 434E, 436, 436B, 436C, 438, 438B, 438C, 442D, 442E, 444E, 902, 906, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH62, TH63, T...
206, 212, 416, 426, 428, 436, 438, AP-800, CB-424, CP-433B, CS-323, CS-431B, PR-75, PS-110, PS-130, PS-180, RT50, WE-601B
9T0421
CYLINDER GP-SWING
428, 438
428, 438
428, 438
206, 416, 428, 436, CB-424, CS-323, PR-75
416, 428, 438
7W4474
CYLINDER BLOCK GP
416, 426, 428
416, 426, 428
9T5216
CYLINDER GP-STICK
416, 428
416, 428
416B, 416C, 416D, 424D, 426, 426B, 428, 428B, 428C, 438C
414E, 416B, 416C, 416D, 416E, 420D, 422E, 424D, 426, 426C, 428, 428B, 428C, 428D, 428E, 430D, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 902, 904B, 904H, 906, 906H, 906H2, 907H, 907H2, 908H...
424D, 428, 428B, 428C, 428D, 432D, 438, 438B, 438C, 438D, 442D