9T6077 CYLINDER GP Caterpillar parts
D8N
Rating:
Alternative (cross code) number:
CA9T6077
9T-6077
9T6077
CA9T6077
9T-6077
9T6077
Weight: 314 pounds 142 kg.
Information:
BORE DIAMETER
165.1
mm
CLOSED LENGTH
1286
mm
PIN SIZE CAP END
69.77
mm
PIN SIZE ROD EYE
113.79
mm
ROD DIAMETER
76.2
mm
STROKE
175
TYPE
BOLTED HEAD
TRACK-TYPE TRACTOR,
Compatible equipment models: 9T6077:
Information:
7. If the number "1" key is pressed, this screen will be displayed. The analyzer will cycle through the solenoids and it will continue to cycle until it finds a fault. At that time the analyzer will stop on the solenoid showing the fault and display the problem. This is a good method for finding intermittent faults.Refer to Step 5 for the different coil conditions.8. When finished with the "AUTO SOLENOID TEST", return to the "SOLENOID TEST MENU" screen by pressing the "SOL TEST" key. This screen will appear.9. If the number "3" key is pressed, this screen will be displayed. The analyzer will prompt the operator to enter a solenoid number. It will then turn ON the selected solenoid. In this mode the analyzer only turns ON the solenoid and does not display a message stating a fault, if one should occur.10. When finished with the "SOLENOID TEST SCREEN", return to the machine information screen by pressing the "MACH INFO" key. This screen will appear.11. Stop here by turning OFF the Transmission Analyzer II or go to another test procedure.Shift Lever Test
The transmission analyzer can be used to test switch assemblies and switch harnesses. However, the shift lever for models with the Autoshift Transmission control feature cannot be tested with the Transmission Analyzer II. These models have diagnostic features on the machine which check the shift lever functions.1. From the selected "MACHINE INFORMATION" screen select "SHIFT LEVER TEST", by pressing the "SHIFT LEVER TEST" key. This screen will appear.2. Select the cable adapters that are best suited for the transmission being tested. Connect the test cables to the machine harness connected to the solenoids. Push the "ENTER" key.3. Move transmission gear selector lever in machine cab to desired gear (for example, 3F). This screen will appear.4. With no gear shift lever connected to the analyzer, the display will show "GEAR SELECTOR PROBLEM".5. When finished with the gear selector test, return to the main information screen by pressing the "MACH INFO" key. This screen will appear.6. Stop here by turning OFF the Transmission Analyzer II or go to another test procedure.Transmission Shift Test
1. From the selected machine menu, select the "TRANSMISSION TEST SCREEN", by pressing the "TRANS TEST" key. This screen will appear.2. Connect the cable called for on the transmission analyzer display (refer to the "Connecting Analyzer Test Cables to Transmission Solenoids" section to connect cables from analyzer to transmission solenoids). Push "ENTER".This screen shows that the Transmission Analyzer II is outputting a signal placing the transmission in "NEUTRAL". Enter the gear number and direction (for example, 1R, 1F, 2F, etc.) at the "ENTER GEAR" prompt; then press the "ENTER" key.Exceptions: For ICM transmissions, Scrapers/Trucks and Articulated Trucks, there is no need to put in the number for direction unless there is more than one reverse gear or neutral.Example: R, N,
The transmission analyzer can be used to test switch assemblies and switch harnesses. However, the shift lever for models with the Autoshift Transmission control feature cannot be tested with the Transmission Analyzer II. These models have diagnostic features on the machine which check the shift lever functions.1. From the selected "MACHINE INFORMATION" screen select "SHIFT LEVER TEST", by pressing the "SHIFT LEVER TEST" key. This screen will appear.2. Select the cable adapters that are best suited for the transmission being tested. Connect the test cables to the machine harness connected to the solenoids. Push the "ENTER" key.3. Move transmission gear selector lever in machine cab to desired gear (for example, 3F). This screen will appear.4. With no gear shift lever connected to the analyzer, the display will show "GEAR SELECTOR PROBLEM".5. When finished with the gear selector test, return to the main information screen by pressing the "MACH INFO" key. This screen will appear.6. Stop here by turning OFF the Transmission Analyzer II or go to another test procedure.Transmission Shift Test
1. From the selected machine menu, select the "TRANSMISSION TEST SCREEN", by pressing the "TRANS TEST" key. This screen will appear.2. Connect the cable called for on the transmission analyzer display (refer to the "Connecting Analyzer Test Cables to Transmission Solenoids" section to connect cables from analyzer to transmission solenoids). Push "ENTER".This screen shows that the Transmission Analyzer II is outputting a signal placing the transmission in "NEUTRAL". Enter the gear number and direction (for example, 1R, 1F, 2F, etc.) at the "ENTER GEAR" prompt; then press the "ENTER" key.Exceptions: For ICM transmissions, Scrapers/Trucks and Articulated Trucks, there is no need to put in the number for direction unless there is more than one reverse gear or neutral.Example: R, N,
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
7W2203
CYLINDER HEAD GP
16G, 16H NA, 245B, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627E, 627F, 814B, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R II, HT400, PM-465, RM-2...
16G, 16H NA, 245B, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627E, 627F, 814B, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R II, HT400, PM-465, RM-2...
7W0009
CYLINDER HEAD AS
16G, 245, 245B, 3406B, 375, 578, 621E, 623E, 627E, 627F, 814B, 824C, 825C, 826C, 980C, 980F, D40D, D8N, RR-250, SM-350, SS-250
16G, 245, 245B, 3406B, 375, 578, 621E, 623E, 627E, 627F, 814B, 824C, 825C, 826C, 980C, 980F, D40D, D8N, RR-250, SM-350, SS-250
6E3113
CYLINDER GP-RIPPER PIN PULLER
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
1105096
CYLINDER HEAD AS
16G, 16H NA, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627F, 814B, 824C, 824G, 825C, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R...
16G, 16H NA, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627F, 814B, 824C, 824G, 825C, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R...
1105099
CYLINDER HEAD AS
16G, 16H NA, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627F, 814B, 824C, 824G, 825C, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R...
16G, 16H NA, 245D, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627F, 814B, 824C, 824G, 825C, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400E, D40D, D8N, D8R, D8R...
9T0142
CYLINDER GP-RIPPER LIFT
D8N, D8R
D8N, D8R
6E1175
CYLINDER GP-TILT
D8N, D8R, D8R II
D8N, D8R, D8R II
9T0143
CYLINDER GP-RIPPER TILT
D8N, D8R
D8N, D8R
2141667
CYLINDER HEAD GP
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623F, 627F, 980C, 980F, 980G, D8N, D8R, D8R II, RM-250C, RR-250B
6E1102
CYLINDER GP-BULLDOZER LIFT
D8N, D8R, D8R II
D8N, D8R, D8R II
6E3976
CYLINDER AS
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
1071822
CYLINDER HEAD AS
3508, 3512, 3516
3508, 3512, 3516
9T7070
CYLINDER GP-STABILIZER-LH
416, 426
416, 426
8R0956
CYLINDER GP-AIR/HYDRAULIC
825C, 826C
825C, 826C
9T4885
CYLINDER GP-EJECTOR
621F, 621G, 627E, 627F, 627G
621F, 621G, 627E, 627F, 627G
3504424
CYLINDER HEAD GP
16H NA, 3406B, 3406C, 621F, 627F, 980C, 980F, D8N
16H NA, 3406B, 3406C, 621F, 627F, 980C, 980F, D8N
1303441
CYLINDER BLOCK GP
3408C, 589
3408C, 589