9T7070 CYLINDER GP-STABILIZER-LH Caterpillar parts
416, 426
Rating:
Alternative (cross code) number:
CA9T7070
9T-7070
9T7070
CA9T7070
9T-7070
9T7070
Weight: 88 pounds 39 kg.
BACKHOE LOADER,
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 -
B - Loctite 263 -
C 9V-3811 Bolt 8 Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Remove the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Personal injury can result from driveline torque windup under load.Unequal wheel speed can result in driveline torque windup which can cause driveline components to be under load during disassembly.Relieve the driveline torque windup before disassembly.
Illustration 2 g01074389
Support rear drive shaft (1). Remove four bolts (2) and four bolts (3).
Use two people to remove rear drive shaft (1). The weight of the rear drive shaft is approximately 27 kg (60 lb).Installation Procedure
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned.
Illustration 3 g01074389
Use two people to position rear drive shaft (1) between the output yoke of the output transfer gears and the rear differential. The weight of the rear drive shaft is approximately 27 kg (60 lb).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (2) prior to installation.Note: Bolts (2) are single use only parts. Discard bolts (2) whenever loosened.
Install bolts (2). Tighten bolts (2) to a torque of 160 15 N m (120 11 lb ft).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (3) prior to installation.Note: Bolts (3) are single use only parts. Discard bolts (3) whenever loosened.
Install bolts (3). Tighten bolts (3) to a torque of 160 15 N m (120 11 lb ft).End By:
Install the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 -
B - Loctite 263 -
C 9V-3811 Bolt 8 Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Remove the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Personal injury can result from driveline torque windup under load.Unequal wheel speed can result in driveline torque windup which can cause driveline components to be under load during disassembly.Relieve the driveline torque windup before disassembly.
Illustration 2 g01074389
Support rear drive shaft (1). Remove four bolts (2) and four bolts (3).
Use two people to remove rear drive shaft (1). The weight of the rear drive shaft is approximately 27 kg (60 lb).Installation Procedure
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned.
Illustration 3 g01074389
Use two people to position rear drive shaft (1) between the output yoke of the output transfer gears and the rear differential. The weight of the rear drive shaft is approximately 27 kg (60 lb).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (2) prior to installation.Note: Bolts (2) are single use only parts. Discard bolts (2) whenever loosened.
Install bolts (2). Tighten bolts (2) to a torque of 160 15 N m (120 11 lb ft).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (3) prior to installation.Note: Bolts (3) are single use only parts. Discard bolts (3) whenever loosened.
Install bolts (3). Tighten bolts (3) to a torque of 160 15 N m (120 11 lb ft).End By:
Install the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Caterpillar SIS machinery equipment:
Parts cylinder Caterpillar catalog:
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 432D, 432E, 434E, 436, 436B, 436C, 438, 438B, 438C, 442D, 442E, 444E, 902, 906, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH62, TH63, T...
206, 212, 416, 426, 428, 436, 438, AP-800, CB-424, CP-433B, CS-323, CS-431B, PR-75, PS-110, PS-130, PS-180, RT50, WE-601B
4T6880
CYLINDER GP-STABILIZER-RH
416, 426
416, 426
1126558
CYLINDER BLOCK GP
416, 426, 428
416, 426, 428
206, 416, 428, 436, CB-424, CS-323, PR-75
6E0099
CYLINDER GP-STABILIZER-RH
416, 416B, 426, 426B, 436, 436B
416, 416B, 426, 426B, 436, 436B
9T7392
CYLINDER GP-STABILIZER-RH
416, 426, 436
416, 426, 436
416, 428, 438
9T7069
CYLINDER GP-STABILIZER-RH
416, 426
416, 426
416B, 416C, 416D, 424D, 426, 426B, 428, 428B, 428C, 438C
414E, 416B, 416C, 416D, 416E, 420D, 422E, 424D, 426, 426C, 428, 428B, 428C, 428D, 428E, 430D, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 902, 904B, 904H, 906, 906H, 906H2, 907H, 907H2, 908H...
4T9911
CYLINDER GP-STABILIZER-LH
416, 426
416, 426
9T7069
CYLINDER GP-STABILIZER-RH
416, 426
416, 426
4T6879
CYLINDER GP-SWING-LH
416, 426, 436
416, 426, 436
9T2215
CYLINDER GP-EXTENSION
416, 426
416, 426
1055739
CYLINDER HEAD GP
AP-1200
AP-1200
1071822
CYLINDER HEAD AS
3508, 3512, 3516
3508, 3512, 3516