9T8785 CYLINDER GP-ARTICULATION Caterpillar parts
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
Rating:
Alternative (cross code) number:
CA9T8785
9T-8785
9T8785
CA9T8785
9T-8785
9T8785
Weight: 53 pounds 24 kg.
Information:
BORE DIAMETER
76.2
mm
CLOSED LENGTH
622.2
mm
PIN SIZE CAP END
38.1
mm
PIN SIZE ROD EYE
38.1
mm
ROD DIAMETER
44.45
mm
STROKE
284.3
TYPE
THD GLAND
MOTOR GRADER,
Compatible equipment models: 9T8785:
Information:
Camshaft And Gears
Start By:a. remove timing gear cover and oil pumpb. remove valve liftersc. remove turbocharger 1. Remove the plug from the fuel injection pump housing, and install timing pin (A).2. While the crankshaft is turned clockwise (as seen from the front of the engine), push on tool (A) until it slides into the groove (slot) in the fuel injection pump camshaft.3. Remove tachometer drive adapter shaft (1). 4. Install tooling (B) into the camshaft drive gear for the fuel injection pump. Turn both bolts evenly until the drive gear is free of the shaft. Remove tooling (B). 5. Remove thrust pin (2) that holds the camshaft in place from the rear of the cylinder block. 6. Remove camshaft (3) and gears from the cylinder block as a unit. Be careful not to cause damage to the camshaft bearing or camshaft lobes. The camshaft gear can be removed from the camshaft if a replacement is necessary.Install Camshaft And Gears
1. Install the camshaft gear on the camshaft if it was removed. Heat the gear to a maximum temperature of 315°C (600°F). Put the gear in position on the camshaft. Put 2P2506 Thread Lubricant on the camshaft lobes. Install camshaft (1) and the gears as a unit. Make sure the timing marks on the crankshaft gear and camshaft gear are in alignment.2. Install the thrust pin. Tighten the pin to a torque of 47 7 N m (35 5 lb.ft.). 3. Put gear (3) in position, and install tachometer drive adapter shaft (2). Tighten the shaft to a torque of 150 14 N m (110 10 lb.ft.). 4. After the valve lifters and timing gear cover have been installed, check the timing as follows:a. Remove timing pin (a).b. Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c. While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft.d. Remove the plug from the timing hole in the front cover, and install a 5/16"-18 NC bolt (4) 2 1/2 in. (64 mm) long. The cover bolt from hole (5) can be used. Check to make sure bolt (4) can be installed into the timing gear and is in the center of the timing hole. The camshaft for the fuel injection pump is now in correct time with the engine.e. Remove the bolt, and install the plug. Remove timing pin (A), and install the plug. If the bolt cannot be installed in the hole of camshaft gear, the timing must be corrected as follows:a. With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b. Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (4) can be installed. Install the bolt.c. Install the tachometer drive adapter shaft, and tighten it to a torque of 150 14 N m (110 10 lb.ft.).
Start By:a. remove timing gear cover and oil pumpb. remove valve liftersc. remove turbocharger 1. Remove the plug from the fuel injection pump housing, and install timing pin (A).2. While the crankshaft is turned clockwise (as seen from the front of the engine), push on tool (A) until it slides into the groove (slot) in the fuel injection pump camshaft.3. Remove tachometer drive adapter shaft (1). 4. Install tooling (B) into the camshaft drive gear for the fuel injection pump. Turn both bolts evenly until the drive gear is free of the shaft. Remove tooling (B). 5. Remove thrust pin (2) that holds the camshaft in place from the rear of the cylinder block. 6. Remove camshaft (3) and gears from the cylinder block as a unit. Be careful not to cause damage to the camshaft bearing or camshaft lobes. The camshaft gear can be removed from the camshaft if a replacement is necessary.Install Camshaft And Gears
1. Install the camshaft gear on the camshaft if it was removed. Heat the gear to a maximum temperature of 315°C (600°F). Put the gear in position on the camshaft. Put 2P2506 Thread Lubricant on the camshaft lobes. Install camshaft (1) and the gears as a unit. Make sure the timing marks on the crankshaft gear and camshaft gear are in alignment.2. Install the thrust pin. Tighten the pin to a torque of 47 7 N m (35 5 lb.ft.). 3. Put gear (3) in position, and install tachometer drive adapter shaft (2). Tighten the shaft to a torque of 150 14 N m (110 10 lb.ft.). 4. After the valve lifters and timing gear cover have been installed, check the timing as follows:a. Remove timing pin (a).b. Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c. While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft.d. Remove the plug from the timing hole in the front cover, and install a 5/16"-18 NC bolt (4) 2 1/2 in. (64 mm) long. The cover bolt from hole (5) can be used. Check to make sure bolt (4) can be installed into the timing gear and is in the center of the timing hole. The camshaft for the fuel injection pump is now in correct time with the engine.e. Remove the bolt, and install the plug. Remove timing pin (A), and install the plug. If the bolt cannot be installed in the hole of camshaft gear, the timing must be corrected as follows:a. With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b. Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (4) can be installed. Install the bolt.c. Install the tachometer drive adapter shaft, and tighten it to a torque of 150 14 N m (110 10 lb.ft.).
Caterpillar SIS machinery equipment:
Caterpillar SIS
120G Motor Grader 11W01251-UP (MACHINE) POWERED BY 3304 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120G Motor Grader 4HD00001-UP (MACHINE) POWERED BY 3304 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 4MK00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
135H Motor Grader 3YK00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 6NM00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 6TM00001-00442 (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
135H Motor Grader 8WN00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 5FM00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 2AN00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Motor Grader 9YR00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120H Series NA Motor Grader 6YN00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
135H Series NA Motor Grader BDJ00001-UP (MACHINE) POWERED BY 3116 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120K Motor Grader SZN00001-UP (MACHINE) POWERED BY C7 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120K Motor Grader JAP00001-UP (MACHINE) POWERED BY C7 Engine »
9T-8785
CYLINDER GP-ARTICULATION
120K Series 2 Motor Grader SZS00001-UP (MACHINE) POWERED BY C7 Engine »
9T-8785
CYLINDER GP-ARTICULATION
Caterpillar parts catalog:
Parts cylinder Caterpillar catalog:
6E1554
CYLINDER GP-ARTICULATION
120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
3G8070
CYLINDER GP-STEERING
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3G4752
CYLINDER GP-WHEEL LEAN
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3G8069
CYLINDER GP-STEERING
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
9J3466
CYLINDER GP-BLADE TIP
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
1052094
CYLINDER GP-SIDESHIFT
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
1630325
CYLINDER AS
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, 924G, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT6...
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, 924G, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT6...
8W0328
CYLINDER-DAMPER
120G, 12G, 130G, 140G, 14G, 160G, 16G, 508
120G, 12G, 130G, 140G, 14G, 160G, 16G, 508
9T2482
CYLINDER AS
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
1050017
CYLINDER
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
1309045
CYLINDER AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
2360737
CYLINDER
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
8X0259
CYLINDER & MTG GP-STEERING
793, 793B, 793C, 793D, 793F, 793F OEM, 793F-XQ
793, 793B, 793C, 793D, 793F, 793F OEM, 793F-XQ
8W2737
CYLINDER & MTG GP-WHEEL LEAN
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
3458414
CYLINDER HEAD GP
140M, 160M, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 340D L, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, 586C, 627G, 637D, 637E, 637G, 814F II, 815F I...
140M, 160M, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 340D L, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, 586C, 627G, 637D, 637E, 637G, 814F II, 815F I...
1108475
CYLINDER & SEAL GP-TILT
980G, 980G II, 980H
980G, 980G II, 980H
1438005
CYLINDER & LINES GP-BUCKET
365B, 365B II, 365B L, 365C, 365C L, 385C
365B, 365B II, 365B L, 365C, 365C L, 385C
1853607
CYLINDER HEAD GP
G3512, G3516
G3512, G3516
3G5192
CYLINDER GP-STEERING
621, 621B, 621E, 621F, 621G, 621H, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H
621, 621B, 621E, 621F, 621G, 621H, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H
1604347
CYLINDER HEAD GP
3406E, 3456, C-15, C-16, D350E II, D400E II
3406E, 3456, C-15, C-16, D350E II, D400E II
3824274
CYLINDER & LINES GP-LIFT
D6T LGPPAT
D6T LGPPAT
4P5125
CYLINDER HEAD AS
3116, 320 L, 928F, 953B, IT28F
3116, 320 L, 928F, 953B, IT28F