AVSPARE.COM
parts catalog

CYLINDER GP-STEERING 9T9019 - Caterpillar


9T9019 CYLINDER GP-STEERING Caterpillar parts 994, 994D, 994F, 994H
Rating:
26
Alternative (cross code) number:
CA9T9019
9T-9019
9T9019
Caterpillar 9T9019 CYLINDER GP-STEERING
Weight: 926 pounds 420 kg.
Information:
BORE DIAMETER  196.85  mm
CLOSED LENGTH  1910  mm
PIN SIZE CAP END  32  mm
PIN SIZE ROD EYE  38  mm
ROD DIAMETER  107.95  mm
STROKE  1120 
TYPE  BOLTED HEAD 

Buy CYLINDER GP-STEERING 9T9019 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9T9019:

WHEEL LOADER  994   994D   994F   994H   Caterpillar
Number on catalog scheme: 1
  For full view, you need register

Information:

Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00828137
Thoroughly clean the top of cylinder block (3) and the bottom of cylinder head (2) . Ensure that there is no debris in the cylinder bores.
Illustration 2 g00828396
Note: A number at location (5) with four digits is stamped on cylinder head gasket (4) in order to ensure the correct positioning of the cylinder head gasket. This number faces the cylinder head. Make sure that cylinder head gasket (4) for cylinder head (2) is the correct thickness as the original cylinder head gasket before installation.Note: Refer to Specifications, "Cylinder Head" in order to determine the thickness of the original cylinder head gasket. Note: The correct piston height must be maintained in order to prevent damage to the pistons and the valves. Refer to Testing and Adjusting, "Piston Height - Inspect". The correct piston height must be maintained in order to ensure that the engine conforms to the exhaust emission standards.
Place cylinder head gasket (4) on the dowels (6) on the top of the cylinder block (3) . Do not use any gasket sealant or compound on the cylinder head gasket.
Attach a suitable lifting device to cylinder head (2) .
Place cylinder head (2) on cylinder block (3) . Ensure that cylinder head (2) is positioned on dowels (6) . Verify that cylinder head gasket (4) is positioned correctly.
Lubricate cylinder head bolts (1) with clean engine oil.
Illustration 3 g00828140
Install cylinder head bolts (1) and gradually tighten the cylinder head bolts in a numerical sequence. The numerical sequence is shown in Illustration 3. Tighten the cylinder head bolts to a torque of 101 N m (74 lb ft).End By:
Install the oil line. Refer to Disassembly and Assembly, "Engine Oil Line - Remove and Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection lines - Remove and Install".
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
994 Wheel Loader 9YF00001-UP (MACHINE) POWERED BY 3516 Engine
994D WHEEL LOADER 3TZ00001-UP (MACHINE) POWERED BY 3516B Engine
994F Wheel Loader 44200001-UP (MACHINE) POWERED BY 3516 Engine
994H Wheel Loader DWC00001-UP (MACHINE) POWERED BY 3516B Engine


Parts cylinder Caterpillar catalog:

3172440 CYLINDER HEAD GP
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H,...
2425328 CYLINDER HEAD AS
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, 994H...
4W0095 CYLINDER HEAD GP
3126, 3508, 3508C, 3512, 3516, 777B, 785, 789, 994, D11N, PM3512, PM3516
2014257 CYLINDER HEAD GP
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, 5130B, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 789C, 793C, 793D, 797, 797B, 854G, 992G, 994D, 994F, D11R, PM3508, PM3512, PM3516, PP3516, ...
4W9560 CYLINDER HEAD GP
3508, 3512, 3516, 777B, 785, 789, 994, D11N
5N8383 CYLINDER
3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 3618, 5230, 5230B, 776C, 776D, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 793B,...
7X1062 CYLINDER AS-ETHER
3408, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D,...
1590888 CYLINDER AS
994, 994D, 994F, 994H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.