4S8536 DAMPER Caterpillar parts
769, 992
Rating:
Alternative (cross code) number:
CA4S8536
4S-8536
4S8536
CA4S8536
4S-8536
4S8536
Weight: 2 pounds 1 kg.
TRUCK, WHEEL LOADER,
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
Drain the engine lubricating oil into a suitable container. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Illustration 1 g01304837
Typical example
Use Tooling (A) to remove oil filter element (5).
Loosen hose clamps (2) and disconnect hoses (1). Note the positions of the coolant inlet and the coolant outlet for installation.
Remove adapter (4) and remove oil cooler (3) from the cylinder block. Note: Make a temporary mark in order to show the orientation of the oil cooler for installation.
Remove O-ring seal (6) from oil cooler (3). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the oil cooler is clean and free from damage. Clean the mating surfaces of the cylinder block.
Illustration 2 g01304837
Typical example
Install a new O-ring seal (6) to oil cooler (3). Position oil cooler (3) on the cylinder block and install adapter (4). Tighten adapter (4) to a torque of 34 N m (25 lb ft). Note: Ensure that the oil cooler is correctly oriented.
Connect hoses (1) to the coolant inlet and the coolant outlet on oil cooler (3). Tighten hose clamps (2).
Install a new oil filter element (5).
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter - Change" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
Drain the engine lubricating oil into a suitable container. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Illustration 1 g01304837
Typical example
Use Tooling (A) to remove oil filter element (5).
Loosen hose clamps (2) and disconnect hoses (1). Note the positions of the coolant inlet and the coolant outlet for installation.
Remove adapter (4) and remove oil cooler (3) from the cylinder block. Note: Make a temporary mark in order to show the orientation of the oil cooler for installation.
Remove O-ring seal (6) from oil cooler (3). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the oil cooler is clean and free from damage. Clean the mating surfaces of the cylinder block.
Illustration 2 g01304837
Typical example
Install a new O-ring seal (6) to oil cooler (3). Position oil cooler (3) on the cylinder block and install adapter (4). Tighten adapter (4) to a torque of 34 N m (25 lb ft). Note: Ensure that the oil cooler is correctly oriented.
Connect hoses (1) to the coolant inlet and the coolant outlet on oil cooler (3). Tighten hose clamps (2).
Install a new oil filter element (5).
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter - Change" for the correct procedure.
Caterpillar parts catalog:
Parts damper Caterpillar catalog:
8S6356
DAMPER
966C
966C
3523557
DAMPER AS
349F L, 730C, 980M, 982M
349F L, 730C, 980M, 982M
950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
7J8680
DAMPER
966F, 970F
966F, 970F
8N1771
DAMPER ASSEM.
814B, 815B, 816B, 966D
814B, 815B, 816B, 966D
1N3632
DAMPER ASSEM.
950B
950B
8N7488
DAMPER ASSEM.
834B, 836, 988B
834B, 836, 988B
7N0960
DAMPER
992C
992C