6I9790 DAMPER-BOLT Caterpillar parts
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 797, 797B, 797F, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 9...
Rating:
Alternative (cross code) number:
CA6I9790
6I-9790
6I9790
CA6I9790
6I-9790
6I9790
Weight: 0.07 pounds 0 kg.
PETROLEUM TRANSMISSION, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 6I9790 Damper B Bolt for Heavy Equipment
CTP Damper B Type of Bolt || Sold in each || Easy in-and-out fit
CTP Damper B Type of Bolt || Sold in each || Easy in-and-out fit
CTP 6I9790 Damper B Bolt for Heavy Equipment
CTP Damper B Type of Bolt || Sold in each || Easy in-and-out fit
CTP Damper B Type of Bolt || Sold in each || Easy in-and-out fit
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 6I9790:
Information:
3200, 3300, 3400, 3500 Series EnginesThe new seal groups are quite different from the former standard lip-type seals. The difference is the hydrodynamic grooves in the sealing lip of the new seal. These grooves in the seal lip move lubrication oil back into the engine crankcase as the crankshaft turns. Because of this seal lip design, the front seal for an engine is different from the rear seal group. The installed position of the seal lip grooves is important, because the grooves are very sensitive to the direction of crankshaft rotation. Each seal is marked with an arrow to show the direction of shaft rotation for which the seal can be used. If a specific seal group is installed on the wrong end of an engine, lubrication oil can actually be taken out of an engine, because the grooves in the seal lip are in the wrong direction in relation to crankshaft rotation. Special handling procedures and seal installation instructions for specific engines are given on the pages that follow.1 Use The Correct Tools For Seal Group Installation
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Cat SIS web machinery list:
Parts damper Caterpillar catalog:
24H, 24M, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5110B, 631D, 631E, 631G, 633E II,...
3408, 3408B, 3412, 589, 631E, 633D, 637D, 651E, 657E, 773B, 834B, 988B, 992C, D8L, D9L, D9N, PR-450, PR-750B
824G II, 824H, 826H, 834G, 834H, 836H, 844, 854G, 966G II, 972G II, 980G II, 988H, 990 II, 992G, C-9, C27, C32, C9, C9.3, CX31-C9I, D10T, D11N, D11R, D8R, D8R II, D9R, R1600, R1600G, R1600H, R1700 II,...
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 776, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM,...
772, 772B, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776, 776C, 776D, 777, 777B, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B...
1407144
DAMPER-BOLT
797, 797B, 797F
797, 797B, 797F
1455192
DAMPER AS
795F AC, 795F XQ, 797, 797B, 797F
795F AC, 795F XQ, 797, 797B, 797F
2283307
DAMPER
793C
793C
1981202
DAMPER AS
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
8W6947
DAMPER-BOLT
785, 789
785, 789
735, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966G, 966G II, 972G, 972G II, 972H, 972K, 972M, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
3482366
DAMPER AS
C15, C18, CX31-C18I, CX35-C18I, D10T2, D9T
C15, C18, CX31-C18I, CX35-C18I, D10T2, D9T
C13, TH35-C13T
2835877
DAMPER AS
C13, TH35-C13T
C13, TH35-C13T
3900455
DAMPER GP
3612
3612
9Y1615
DAMPER & GUARD AS
3608, G3616
3608, G3616
120G, 12G, 130G, 14G, 1673C, 215, 225, 235, 3304, 3306, 3412, 518, 561C, 621R, 627, 627B, 637D, 920, 930, 950, 955K, 955L, 966C, 980B, D4D, D5, D5B, D6C, D7F, D7G
120G, 130G, 1673C, 215, 225, 3304, 3306, 518, 561C, 621R, 627, 920, 930, 950, 955K, 955L, 966C, D4D, D5, D5B, D6C, D7F, D7G
16, 1693, 621, 631C, 824B, 980, 983, 988, D343
3907032
DAMPER
Caterpillar
Caterpillar
3572382
DAMPER AS
C13, CX31-C13I
C13, CX31-C13I
3518695
DAMPER AS
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 730C, 980K, 980K HLG, C13, CX31-C13I
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 730C, 980K, 980K HLG, C13, CX31-C13I