2764408 DEFLECTOR GP-DEBRIS Caterpillar parts
PR190
Rating:
Alternative (cross code) number:
CA2764408
276-4408
2764408
CA2764408
276-4408
2764408
RAKE-POWER BOX,
Compatible equipment models: 2764408:
Number on catalog scheme:
2
For full view, you need register
Information:
Spreader Bar
Illustration 1 g02175782
Improper lifting and improper tie-downs can allow the load to shift or fail and cause injury or damage. Use only properly rated cables and slings with lift and tie down points provided.Follow the instructions in Operation and Maintenance Manual, "Lifting and Tying Down the Machine" for the proper technique for securing the machine. Refer to Operation and Maintenance Manual, "Specifications" for specific weight information.
Illustration 2 g03477216This lifting method is the preferred method to be used for all machines. This method is the only method acceptable on machines that are equipped with threaded bosses (1) located on the counterweight.Note: The threaded bosses must only be used to remove the counterweight. These bosses will not support the weight of the machine.Note: The shipping weight that is listed is the weight of the most common configuration of the machine. If attachments have been installed on your machine, the weight of your machine and the center of gravity of your machine may vary.Refer to the Operation and Maintenance Manual, "Specifications" for specific weight information.
Use correctly rated cables and slings for lifting. The crane should be positioned so that the machine is lifted parallel to the ground.
To prevent contact with the machine, lifting cables should have sufficient length.
The width of the spreader bar and the strength of the spreader bar should be sufficient to prevent contact with the machine. When the wire cables are lifted, the wire cables should slide to front track rollers and to the rear track rollers.
Move the lever for the hydraulic lockout control to the LOCKED position. Note: Never use the step as a lifting point for lifting the machine.Lifting the Machine Segments
Bucket
Illustration 3 g01587173
(1) Sleeve
(2) Bolts
(3) Pin
(4) Nuts Install pin (3) and install sleeve (1) in the brackets of the bucket. The previous illustration indicates the method to secure pin (3) with bolts (2) and nuts (4). Fasten two proper rated wire cables to pin (3).Note: Never use the step as a lifting point for lifting the machine.
Illustration 1 g02175782
Improper lifting and improper tie-downs can allow the load to shift or fail and cause injury or damage. Use only properly rated cables and slings with lift and tie down points provided.Follow the instructions in Operation and Maintenance Manual, "Lifting and Tying Down the Machine" for the proper technique for securing the machine. Refer to Operation and Maintenance Manual, "Specifications" for specific weight information.
Illustration 2 g03477216This lifting method is the preferred method to be used for all machines. This method is the only method acceptable on machines that are equipped with threaded bosses (1) located on the counterweight.Note: The threaded bosses must only be used to remove the counterweight. These bosses will not support the weight of the machine.Note: The shipping weight that is listed is the weight of the most common configuration of the machine. If attachments have been installed on your machine, the weight of your machine and the center of gravity of your machine may vary.Refer to the Operation and Maintenance Manual, "Specifications" for specific weight information.
Use correctly rated cables and slings for lifting. The crane should be positioned so that the machine is lifted parallel to the ground.
To prevent contact with the machine, lifting cables should have sufficient length.
The width of the spreader bar and the strength of the spreader bar should be sufficient to prevent contact with the machine. When the wire cables are lifted, the wire cables should slide to front track rollers and to the rear track rollers.
Move the lever for the hydraulic lockout control to the LOCKED position. Note: Never use the step as a lifting point for lifting the machine.Lifting the Machine Segments
Bucket
Illustration 3 g01587173
(1) Sleeve
(2) Bolts
(3) Pin
(4) Nuts Install pin (3) and install sleeve (1) in the brackets of the bucket. The previous illustration indicates the method to secure pin (3) with bolts (2) and nuts (4). Fasten two proper rated wire cables to pin (3).Note: Never use the step as a lifting point for lifting the machine.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts deflector Caterpillar catalog:
3745372
DEFLECTOR GP-FENDER
950H, 962H
950H, 962H
2135600
DEFLECTOR GP
613C II
613C II
4361889
DEFLECTOR GP
AD30
AD30