AVSPARE.COM
parts catalog

DETECTOR GP-OIL MIST 2500823 - Caterpillar



2500823 DETECTOR GP-OIL MIST Caterpillar parts 3616 DETECTOR
Rating:
20
Alternative (cross code) number:
CA2500823
250-0823
2500823
Caterpillar 2500823 DETECTOR GP-OIL MIST

Buy DETECTOR GP-OIL MIST 2500823 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 2500823:

MARINE ENGINE  3616   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Ensure that the nitrogen oxide sensor is not dropped or knocked. If the nitrogen oxide sensor, has been dropped or knocked the nitrogen oxide sensor must be replaced as an assembly.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g03731237
Typical example
Illustration 2 g03731236
Typical example
Remove nitrogen oxide sensor (6) from exhaust tube assembly (7). Ensure that the harness assembly is not damaged as the nitrogen oxide sensor is removed. Place the probe of the nitrogen oxide sensor in a plastic bag and secure the plastic bag with a cable strap.
If necessary, follow Step 4.a through Step 4.c in order to remove nitrogen oxide sensor Electronic Control Module (ECM) (2).
Disconnect Original Equipment Manufacture (OEM) harness assembly (3) from the nitrogen oxide sensor ECM (2).
Cut cable straps (1) from the harness assembly. Note the position of all cable straps for installation purposes. Note: Ensure that the harness assembly is not damaged as the cable straps are cut.
Remove bolts (4) nitrogen oxide sensor ECM (2). Remove the nitrogen oxide sensor ECM from bracket (5). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Bostik Pure Nickel
Anti-Seize Compound 1
B - 22 mm Crows Foot 1
Ensure that the nitrogen oxide sensor is free from wear or damage. Replace the nitrogen oxide sensor as an assembly if worn or damaged.
Check the threads of the mounting point for nitrogen oxide sensor in the exhaust elbow. Replace the elbow if the mounting point is worn or damage.
Illustration 3 g03731237
Typical example
Illustration 4 g03731236
Typical example
If necessary, follow Step 3.a through Step 3.c in order to install nitrogen oxide sensor ECM (2).
Position nitrogen oxide sensor ECM (2) onto bracket (5). Ensure that the nitrogen oxide sensor ECM is correctly orientated onto the bracket.
Install bolts (4) to nitrogen oxide sensor ECM (2). Support the nitrogen oxide sensor ECM as the bolts are installed. Tighten the bolts to a torque of 10 N m (89 lb in).
Connect OEM harness assembly (3) to nitrogen oxide sensor ECM (2).
New nitrogen oxide sensor (6) are pre-lubricated. When installing an existing nitrogen oxide sensor (6), lightly lubricate the thread of the nitrogen oxide sensor with Tooling (A). Note: Ensure that the nitrogen oxide sensor is not contaminated.
Remove the probe of nitrogen oxide sensor (6) from the plastic bag. Install the nitrogen oxide sensor to exhaust tube assembly (7). Ensure that the harness assembly is not damaged as the nitrogen oxide sensor is installed.
Use Tooling (B) to tighten nitrogen oxide sensor (6) to a torque of 50 N m (37 lb ft).
Install new cable straps (1) to the harness assembly. Ensure that the cable straps are installed into the original position. Note: Ensure that the cable straps meet OEM specifications.
Turn the battery disconnect switch to the ON position.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts detector Caterpillar catalog:

4P9190 DETECTOR GP-LIQUID
3606, 3608, 3612, 3616
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.