1094717 DIFFERENTIAL GP Caterpillar parts
910G, 914G, IT14G
Rating:
Alternative (cross code) number:
CA1094717
109-4717
1094717
CA1094717
109-4717
1094717
COMPACT WHEEL LOADER, INTEGRATED TOOLCARRIER,
Compatible equipment models: 1094717:
Information:
Personal injury or death could result when towing a disabled machine incorrectly.Block the machine to prevent movement before releasing the brakes. The machine can roll free if it is not blocked.Follow the recommendations below, to properly perform the towing procedure.Be sure all necessary repairs and adjustments have been made before a machine that has been towed to a service area, is put back into operation.
This machine is equipped with spring applied, hydraulic pressure released brakes. If the engine is inoperable or auxiliary system pressure drops below 8613 kPa (1250 psi), the brakes are applied and the machine cannot be moved.These towing instructions are for moving a disabled machine a short distance, only a few meters (feet) at very low speed, no faster than 2 km/h (1.2 mph), to a convenient location for repair. These instructions are for emergencies only. Always haul the machine if long distance moving is required.Shielding must be provided on the towing machine, to protect the operator if the tow line or bar should break.Do not allow operator on the machine being towed, unless the operator can control the steering and/or braking.Before towing, make sure the tow line or bar is in good condition and has enough strength for the towing situation involved. Use a towing line or bar with a strength of at least 1.5 times the gross weight of the towing machine, for a disabled machine stuck in mud or when towing on a grade.When towing, attach the tow line only to the tow eyes on the frame. The front tow eye is centered below the radiator grill. The rear tow eye is centered above the bearings in the rear bolster oscillation joint.Do not use a chain for pulling. A chain link can break causing possible personal injury. Use a wire rope cable with loop or ring ends. Use an observer in a safe position to stop the pulling procedure if the cable starts to break or unravel. Stop pulling whenever the pulling machine moves without moving the towed machine.Keep the tow line angle to a minimum. Do not exceed a 30° angle from the straight ahead position.Quick machine movement could overload the tow line or bar and cause it to break. Gradual and smooth machine movement will work better.Normally, the towing machine should be as large as the disabled machine. Satisfy yourself that the towing machine has enough brake capacity, weight and power, to control both machines for the grade and distance involved.To provide sufficient control and braking when moving a disabled machine downhill, a larger towing machine or additional machines connected to the rear could be required. This will prevent it from rolling uncontrolled.The different situation requirements cannot be given, as minimal towing machine capacity is required on smooth level surfaces to maximum on inclines or poor surface conditions.Consult your Caterpillar dealer for towing a disabled machine. Engine RunningIf the propel and steering systems are operable, and the engine is running, the machine can be towed a SHORT DISTANCE, pulled out
Caterpillar SIS machinery equipment:
Caterpillar SIS
914G Wheel Loader 7ZM00001-00439 (MACHINE) POWERED BY 3054 Engine »
109-4717
DIFFERENTIAL GP
IT14G Integrated Toolcarrier 1WN00001-00659 (MACHINE) POWERED BY 3054 Engine »
109-4717
DIFFERENTIAL GP
910G Wheel Loader AKR00001-UP (MACHINE) POWERED BY 3064 Engine »
109-4717
DIFFERENTIAL GP
IT14G Integrated Toolcarrier 1WN00660-UP (MACHINE) »
109-4717
DIFFERENTIAL GP
914G Wheel Loader 7ZM00440-UP (MACHINE) POWERED BY 3054 Engine »
109-4717
DIFFERENTIAL GP
914G Wheel Loader PDF00001-UP (MACHINE) POWERED BY 3054C Engine »
109-4717
DIFFERENTIAL GP
IT14G Integrated Tool Carrier FWL00001-UP (MACHINE) POWERED BY 3054C Engine »
109-4717
DIFFERENTIAL GP
Caterpillar parts catalog:
Parts differential Caterpillar catalog:
1175786
DIFFERENTIAL GP-NOSPIN
924F, 924G, 924GZ, IT24F
924F, 924G, 924GZ, IT24F
8W5587
DIFFERENTIAL GP
120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
1071958
DIFFERENTIAL AR
950F II, 960F
950F II, 960F
1071957
DIFFERENTIAL AR
950F II, 960F
950F II, 960F
1119253
DIFFERENTIAL AR-REAR
938F, 938G, IT38F, IT38G
938F, 938G, IT38F, IT38G
2379201
DIFFERENTIAL GP-LIMITED SLIP
914G, IT14G
914G, IT14G
1185025
DIFFERENTIAL GP-LIMITED SLIP
914G, IT14G
914G, IT14G
2379202
DIFFERENTIAL GP
914G, IT14G, IT14G2
914G, IT14G, IT14G2