AVSPARE.COM
parts catalog

DIFFERENTIAL & BEVEL GEAR GP 3874496 - Caterpillar


3874496 DIFFERENTIAL & BEVEL GEAR GP Caterpillar parts 16M
Rating:
28
Alternative (cross code) number:
CA3874496
387-4496
3874496
Caterpillar 3874496 DIFFERENTIAL & BEVEL GEAR GP

Buy DIFFERENTIAL & BEVEL GEAR GP 3874496 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 3874496:

MOTOR GRADER  16M   Caterpillar
Number on catalog scheme: 5
  For full view, you need register

Information:


Illustration 1 g00678190
Schematic of the Machine Autolube Pressure Sensor
This diagnostic code is recorded when the VIMS ECM reads the sensor signal and the voltage is too low. The possible causes of this failure are listed below:
The sensor has failed.
The signal circuit is shorted to ground.
The ECM has failed.System Response:The failure causes the machine autolube pressure sensor to always indicate the maximum pressure or this failure causes the machine autolube pressure sensor to intermittently indicate the maximum pressure. Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the machine harness from the sensor. Expected Result:The diagnostic code changes from CID 0379 FMI 04 to CID 0379 FMI 03. Results:
OK - The diagnostic code changes from "CID 0379 FMI 04" to "CID 0379 FMI 03". Repair: The failure is no longer present. The sensor has failed. perform the Testing and Adjusting, "Pulse Width Modulated (PWM) Sensor-Test" procedure prior to replacing the sensor. STOP
NOT OK - The diagnostic code "CID 0379 FMI 04" is still active. Proceed to test step 2.Test Step 2. CHECK THE HARNESS.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
At the harness connector for the sensor, measure the resistance between the signal contact C (wire F456-WH(White)) and frame ground. Expected Result:The resistance is greater than 5000 ohms. STOP. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Repair: The ECM has failed. It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the fault is not found, replace the ECM. See Testing and Adjustment, "Module - Replace". STOP
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. Repair: There is a short between frame ground and the signal circuit in the machine harness. Repair the machine harness or replace the machine harness. STOP

Caterpillar parts catalog:

Caterpillar parts catalog
16M Motor Grader R9H00001-UP (MACHINE) POWERED BY C13 Engine
16M Series 3 Motor Grader E9Y00001-UP (MACHINE) POWERED BY C13 Engine
16M Series 3 Motor Grader N9Y00001-UP (MACHINE) POWERED BY C13 Engine
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
18M Series 3 Motor Grader E9W00001-UP (MACHINE) POWERED BY C13 Engine


Parts differential Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.