2178082 DISC-BRAKE Caterpillar parts
902, 906, 908
Rating:
Alternative (cross code) number:
CA2178082
217-8082
2178082
CA2178082
217-8082
2178082
Weight: 22 pounds 10 kg.
COMPACT WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 2178082 Disc Brake for Braking and Steering System
CTP For Braking and Steering System || Highly Efficient || Easy in-and-out fit
CTP For Braking and Steering System || Highly Efficient || Easy in-and-out fit
CTP 2178082 Disc Brake for Braking and Steering System
CTP For Braking and Steering System || Highly Efficient || Easy in-and-out fit
CTP For Braking and Steering System || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
9
For full view, you need register
Information:
Put 9S3263 Thread Lock on the threads of all studs before installing in the block:(1) Thickness of spacer plate ... .5142 .0010 in.(13.061 0.025 mm)Torque for two bolts through rear of each spacer plate (1) into the block ... 35 5 lb.ft.(45 7 N m)Thickness of gasket between spacer plate (1) and block ... .008 .001 in.(0.20 0.03 mm) There must not be any fuel, water, oil, gasket adhesive or any other material on the bottom of the plate, top of the block and both sides of gasket during assembly.For height of liner over spacer plate (1), make reference to CYLINDER LINER PROJECTION.(2) Torque for studs ... 20 3 lb.ft.(25 4 N m)(3) Bore in block for main bearing with standard outside diameter ... 5.6345 .0005 in.(143.116 0.013 mm) Bore in block for .025 in. (0.64 mm) oversize (larger than standard outside diameter) main bearing ... 5.6595 .0005 in.(143.751 0.013 mm)(4) Dimension (new) from center of main bearing bore to top of block below spacer plate (top decks) ... 19.478 .002 in.(497.74 0.05 mm)(5) Dimension (new) from center of main bearing bore to bottom of block (pan rails) ... 8.000 .001 in.(203.20 0.03 mm)Make reference to issue of SERVICE MAGAZINE, May 15, 1975 (Form No. SEBD1512) for ENGINE REBUILD PROCEDURES on D346, D348 and D349 engines. (6) Clearance between the main bearing caps and their respective slots must be .0018 in. (0.048 mm) tight to .0012 in. (0.030 mm) loose. Torque for main bearing studs ... 170 20 lb.ft.(230 25 N m)Torque for nuts holding caps for main bearings:Tighten bearing nuts in sequence ... A, B, C, Da. Put 5P960 Grease or crankcase oil on threads and washers.b. Tighten all nuts in correct sequence to ... 60 5 lb.ft.(80 7 N m)c. Put mark on each nut and ends of studs.d. Tighten all nuts in correct sequence from mark ... 120°(7) Torque for bolt holding piston cooling tube ... 35 5 lb.ft.(45 7 N m)Minimum permissible clearance between piston and piston cooling tube ... .025 in.(0.64 mm) Be sure that the correct piston cooling tubes are installed. The procedure for checking the clearance is in Special Instructions (GEG02495).
Caterpillar parts catalog:
Parts disc Caterpillar catalog:
1657067
DISC-BRAKE
906H, 906H2, 907H, 907H2, 908, 908H, 908H2
906H, 906H2, 907H, 907H2, 908, 908H, 908H2
517, 527, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966H, 966K, IT62G, IT62G II
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
928G, 928H, 928HZ, 930G, 930K, IT28G
928G, IT28G
1289522
DISC-FRICTION
910G, 914G, IT14G, IT14G2
910G, 914G, IT14G, IT14G2
924F, 924G, 924H, 924HZ, 928G, 928H, 928HZ, 930G, IT24F, IT28G
924G, 924GZ
924G, 924GZ, 924H, 924HZ, 924K
1657067
DISC-BRAKE
906H, 906H2, 907H, 907H2, 908, 908H, 908H2
906H, 906H2, 907H, 907H2, 908, 908H, 908H2
1046743
DISC
928F, 928G, IT28G
928F, 928G, IT28G
1046744
DISC
928F, 928G, IT28G
928F, 928G, IT28G
1700048
DISC-FRICTION
928G, 928HZ, IT28G
928G, 928HZ, IT28G