4826732 DISC Caterpillar parts
Rating:
Alternative (cross code) number:
CA4826732
482-6732
4826732
CA4826732
482-6732
4826732
Weight: 3 pounds 1 kg.
Information:
Machine Preparation
Park the machine on a smooth, level surface.
Shift the transmission direction control switch to the NEUTRAL position.
Lower the bucket or the work tool to the ground.
Engage the parking brake.
Allow only authorized personnel on the machine. Keep unauthorized personnel off the machine and in clear sight of the operator.
Shut off the engine. Note: This calibration procedure can be performed without a running engine.
Turn the key start switch and the disconnect switch to the ON position. Procedure for Setting the Values of the Reduced Rimpull Select Button
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.Prevent possible injury by performing the procedure that follows before working on the machine.
Illustration 1 g02631959
Location of Advisor Module
(1) Advisor Module
(2) Reduced Rimpull keypad button
Illustration 2 g02612456
Location of service connector
(2) Reduced Rimpull keypad button
(6) Service connector
(7) 12 V power source
Illustration 3 g02625856
(2) Reduced Rimpull keypad button
(3) LED 1
(4) LED 2
(5) LED 3
When no LED's are lit, you are in the Position 1 (Low) setting.
When LED 1 is lit, you are in the Position 2 (Med Low) setting.
When LED 1 and LED 2 are lit, you are in the Position 3 (Med High) setting.
When all three LED's are lit, you are in the Position 4 (100%) setting.
Press the "Home" button on the Advisor module to return to the top menu. Note: Reduced rimpull settings can be stored to an operator profile in advisor. Before proceeding, select or create the profile that the reduced rimpull settings will be associated with. For more information about profiles, refer to Systems Operation, UENR0787, "VIMSTM 3G / Product Link" your machine.
Select the "Settings" menu at the top menu. Press the "OK" button.
Select the "Operator Config" menu under the "Settings" menu. Press the "OK" button.
Select the "Reduced Rimpull" menu under the "Operator Config". Press the "OK" button.
Follow the instructions on the Advisor module to change the rimpull values for each setting. Note: Advisor will not allow the reduced rimpull value at a lower setting to be set to a value that is higher than the value at a higher setting. Make sure that the values of the reduced rimpull settings increase from the lowest setting to the highest setting.
When all the reduced rimpull settings are modified, press the "HOME" button to return to the top menu.
Select the "Operator Config" menu at the top menu. Press the "OK" button.
Select the "View/Save Current" menu under "Operator" menu. Press the "OK" button.
Review the reduced rimpull settings to ensure that the rimpull setting are set properly. Follow the instructions on the Advisor module to save the changes under the current operator profile.
Park the machine on a smooth, level surface.
Shift the transmission direction control switch to the NEUTRAL position.
Lower the bucket or the work tool to the ground.
Engage the parking brake.
Allow only authorized personnel on the machine. Keep unauthorized personnel off the machine and in clear sight of the operator.
Shut off the engine. Note: This calibration procedure can be performed without a running engine.
Turn the key start switch and the disconnect switch to the ON position. Procedure for Setting the Values of the Reduced Rimpull Select Button
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.Prevent possible injury by performing the procedure that follows before working on the machine.
Illustration 1 g02631959
Location of Advisor Module
(1) Advisor Module
(2) Reduced Rimpull keypad button
Illustration 2 g02612456
Location of service connector
(2) Reduced Rimpull keypad button
(6) Service connector
(7) 12 V power source
Illustration 3 g02625856
(2) Reduced Rimpull keypad button
(3) LED 1
(4) LED 2
(5) LED 3
When no LED's are lit, you are in the Position 1 (Low) setting.
When LED 1 is lit, you are in the Position 2 (Med Low) setting.
When LED 1 and LED 2 are lit, you are in the Position 3 (Med High) setting.
When all three LED's are lit, you are in the Position 4 (100%) setting.
Press the "Home" button on the Advisor module to return to the top menu. Note: Reduced rimpull settings can be stored to an operator profile in advisor. Before proceeding, select or create the profile that the reduced rimpull settings will be associated with. For more information about profiles, refer to Systems Operation, UENR0787, "VIMSTM 3G / Product Link" your machine.
Select the "Settings" menu at the top menu. Press the "OK" button.
Select the "Operator Config" menu under the "Settings" menu. Press the "OK" button.
Select the "Reduced Rimpull" menu under the "Operator Config". Press the "OK" button.
Follow the instructions on the Advisor module to change the rimpull values for each setting. Note: Advisor will not allow the reduced rimpull value at a lower setting to be set to a value that is higher than the value at a higher setting. Make sure that the values of the reduced rimpull settings increase from the lowest setting to the highest setting.
When all the reduced rimpull settings are modified, press the "HOME" button to return to the top menu.
Select the "Operator Config" menu at the top menu. Press the "OK" button.
Select the "View/Save Current" menu under "Operator" menu. Press the "OK" button.
Review the reduced rimpull settings to ensure that the rimpull setting are set properly. Follow the instructions on the Advisor module to save the changes under the current operator profile.
Caterpillar parts catalog:
Parts disc Caterpillar catalog:
4505387
DISC-CLUTCH
Caterpillar
Caterpillar
3921744
DISC-FRICTION
Caterpillar
Caterpillar
3853942
DISC-FRICTION
Caterpillar
Caterpillar
3853940
DISC-FRICTION
Caterpillar
Caterpillar
3816725
DISC-FRICTION
Caterpillar
Caterpillar
3651806
DISC-FRICTION
Caterpillar
Caterpillar
3773136
DISC
Caterpillar
Caterpillar
5609543
DISC-CLUTCH
Caterpillar
Caterpillar
5609542
DISC-CLUTCH
Caterpillar
Caterpillar
4900400
DISC-CLUTCH
Caterpillar
Caterpillar