4S9074 DISC ASSEM. Caterpillar parts
561C, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
Rating:
Alternative (cross code) number:
CA4S9074
4S-9074
4S9074
CA4S9074
4S-9074
4S9074
Weight: 0.20 pounds 0 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$91.60
30 Jan 2024
US: Florida-Parts-Z
2H6121 - DISC Assy 4S9072 1S8183 4H2923 4S9074 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$91.60
28 Dec 2023
US: Florida-Parts-Z
4S9074 - DISC Assy 4S9072 1S8183 2H6121 4H2923 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 4S9074:
Information:
System Operation Description:This section contains steps that can be used to help determine the possible cause of erratic reports of interval. Check for active diagnostic codes for the Product Link. Correct any diagnostic codes before proceeding. The following items should be visually inspected for damage: PL121SR radio, PL300 module, antenna, and cables. Verify that there are no loose connections.The Product Link system depends on several communication links to transfer data from the machine to the office. The following procedures assume that these communication links are operating properly. The proper communication links are listed below:
The satellite network for VHF communications is operational in the geographic area of concern. The network is operational when messages can travel to the satellite and the messages can travel to the earth and Caterpillar.
The Product Link system is correctly configured to communicate on the network for VHF communications. This was verified during manufacturing tests.
The worldwide network of Caterpillar's computers is passing messages to the software for the Caterpillar Equipment Manager (EM).
EM is configured properly and the software is functioning.The Product Link module nor the radio should not be replaced without verifying that these issues have been investigated. Contact the Caterpillar Technical Communicator for aid in resolving these issues.Refer to the Product Link device configuration and status information in Systems Operation, Troubleshooting, Testing and Adjusting, RENR7911, "Diagnostic Capabilities" to ensure that the lack of reporting is not due to the power mode. The unit is likely to have been configured correctly if the following statements exist:
There is no position report after moving the machine ("Position Report Minimum Location Change").
The SMH report is received.There is likely to be a problem with the systems GPS. Proceed with the following steps to determine the cause:Test Step 1. ACCESS THE PRODUCT LINK THROUGH CAT® ELECTRONIC TECHNICIAN (CAT ET).
Connect the Cat ET service tool to the machine.
Verify that the ECM (Product Link) is available.Expected Result:The ECM (Product Link) is available.Results:
OK - The ECM (Product Link) is available. Proceed to Test Step 3.
NOT OK - The ECM (Product Link) is not present in the Cat ET screen.Repair: Verify that the wiring for the Product Link has been installed correctly. Check the wiring with a multimeter. If the ECM ( Product Link) is not available, refer to Systems Operation, Troubleshooting, Testing and Adjusting, "Electronic Service Tool Does Not Communicate with ECM".STOPTest Step 2. VERIFY IF THE MACHINE HAS MOVEDVerify if the machine has moved more than the configured minimum distance ("Position Report Minimum Location Change") since the last known Position Report.Expected Result:The machine has not moved.Results:
OK - The machine has moved less than the configured minimum distance ("Position Report Minimum Location Change") since the last known position report. Therefore, the machine has not sent any position reports.STOP
NOT OK - The machine has moved more than the "Position Report Minimum Location Change" or machine movement is unknown. Proceed to Test Step 3.Test Step 3. VERIFY THAT THE PRODUCT LINK MODULE IS IN POWER MODE 1.
Select "Status Parameters" for Cat ET.
Verify that the "Power
The satellite network for VHF communications is operational in the geographic area of concern. The network is operational when messages can travel to the satellite and the messages can travel to the earth and Caterpillar.
The Product Link system is correctly configured to communicate on the network for VHF communications. This was verified during manufacturing tests.
The worldwide network of Caterpillar's computers is passing messages to the software for the Caterpillar Equipment Manager (EM).
EM is configured properly and the software is functioning.The Product Link module nor the radio should not be replaced without verifying that these issues have been investigated. Contact the Caterpillar Technical Communicator for aid in resolving these issues.Refer to the Product Link device configuration and status information in Systems Operation, Troubleshooting, Testing and Adjusting, RENR7911, "Diagnostic Capabilities" to ensure that the lack of reporting is not due to the power mode. The unit is likely to have been configured correctly if the following statements exist:
There is no position report after moving the machine ("Position Report Minimum Location Change").
The SMH report is received.There is likely to be a problem with the systems GPS. Proceed with the following steps to determine the cause:Test Step 1. ACCESS THE PRODUCT LINK THROUGH CAT® ELECTRONIC TECHNICIAN (CAT ET).
Connect the Cat ET service tool to the machine.
Verify that the ECM (Product Link) is available.Expected Result:The ECM (Product Link) is available.Results:
OK - The ECM (Product Link) is available. Proceed to Test Step 3.
NOT OK - The ECM (Product Link) is not present in the Cat ET screen.Repair: Verify that the wiring for the Product Link has been installed correctly. Check the wiring with a multimeter. If the ECM ( Product Link) is not available, refer to Systems Operation, Troubleshooting, Testing and Adjusting, "Electronic Service Tool Does Not Communicate with ECM".STOPTest Step 2. VERIFY IF THE MACHINE HAS MOVEDVerify if the machine has moved more than the configured minimum distance ("Position Report Minimum Location Change") since the last known Position Report.Expected Result:The machine has not moved.Results:
OK - The machine has moved less than the configured minimum distance ("Position Report Minimum Location Change") since the last known position report. Therefore, the machine has not sent any position reports.STOP
NOT OK - The machine has moved more than the "Position Report Minimum Location Change" or machine movement is unknown. Proceed to Test Step 3.Test Step 3. VERIFY THAT THE PRODUCT LINK MODULE IS IN POWER MODE 1.
Select "Status Parameters" for Cat ET.
Verify that the "Power
Cat SIS web machinery list:
Parts disc Caterpillar catalog:
4S9072
DISC-FRICTION
D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7G
D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7G
9P9382
DISC-FRICTION
983B, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G SR, D7G
983B, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G SR, D7G
1A3987
DISC
118, 127, 25, 30, 561B, 561C, 572G, 619, 977D, 977H, 977K, 977L, 983, 983B, D5, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
118, 127, 25, 30, 561B, 561C, 572G, 619, 977D, 977H, 977K, 977L, 983, 983B, D5, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
5K8616
DISC
931B, 933, 939, 941, 951B, 955L, D3C III, D4C III, D4D, D4E, D4E SR, D5C, D5C III
931B, 933, 939, 941, 951B, 955L, D3C III, D4C III, D4D, D4E, D4E SR, D5C, D5C III
5V0593
DISC AS-CLUTCH
931B, 933, 939, 951B, 955L, D3C III, D4C III, D4E, D5C, D5C III
931B, 933, 939, 951B, 955L, D3C III, D4C III, D4E, D5C, D5C III
3F5504
DISC ASSEM.
24, 941, 955C, 955H, D4D
24, 941, 955C, 955H, D4D
2H6936
DISC (8 TEETH)
931B, 941, 955C, 955H, D3, D3B, D4D
931B, 941, 955C, 955H, D3, D3B, D4D
2F8621
DISC ASSEMBLY-CLUTCH
25, 561B, 561C, 977D, 977H, D5
25, 561B, 561C, 977D, 977H, D5
5K8617
DISC ASSEM. (95 Teeth)
941, 951B, 955L, D4D, D4E, D4E SR
941, 951B, 955L, D4D, D4E, D4E SR
3S1691
DISC
977K, D6C
977K, D6C
5M1199
DISC ASSEM.
977H, 977K, 977L, D5B, D6C, D6D
977H, 977K, 977L, D5B, D6C, D6D
2P4371
DISC ASSEM.
55, 57, 58, 594H, D5B, D6D, D7G, D8L, D9L
55, 57, 58, 594H, D5B, D6D, D7G, D8L, D9L
5J9261
DISC
955K, 955L, 977K, 980B, 983, 988, 992, 992C, 992D
955K, 955L, 977K, 980B, 983, 988, 992, 992C, 992D
5M6122
DISC ASSEM.
14E, 621, 621B, 621E, 621F, 621R, 623, 623B, 623E, 627, 627B, 627E, 637B, 637D, 977K, 980, 980B, D6C, D6D
14E, 621, 621B, 621E, 621F, 621R, 623, 623B, 623E, 627, 627B, 627E, 637B, 637D, 977K, 980, 980B, D6C, D6D
5M1199
DISC ASSEM.
977H, 977K, 977L, D5B, D6C, D6D
977H, 977K, 977L, D5B, D6C, D6D
3S1691
DISC
977K, D6C
977K, D6C
3S7981
DISC ASSEM.
12F, 14E, 518, 518C, 528, 528B, 530B, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 920, 930, 941, 951B, AD55B, AD60, D4D, D4E
12F, 14E, 518, 518C, 528, 528B, 530B, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 920, 930, 941, 951B, AD55B, AD60, D4D, D4E
5K8617
DISC ASSEM. (95 Teeth)
941, 951B, 955L, D4D, D4E, D4E SR
941, 951B, 955L, D4D, D4E, D4E SR
2J5263
DISC
118, 119, 128, 129
118, 119, 128, 129
2J5262
DISC
118, 119, 128, 129
118, 119, 128, 129
2J5513
DISC. ASSEM.
118, 127, 25, 30, 619
118, 127, 25, 30, 619
4K1317
DISC
955H, 955K, 955L
955H, 955K, 955L
8M5070
DISC ASSEM.
594, 594H, D8H, D8K, D9G, D9H
594, 594H, D8H, D8K, D9G, D9H
8M5047
DISC ASSEM.
594, 651, 657, 834, 992, D8H, D9G
594, 651, 657, 834, 992, D8H, D9G