6T8886 DISC Caterpillar parts
583K, D8K
Rating:
Alternative (cross code) number:
CA6T8886
6T-8886
6T8886
CA6T8886
6T-8886
6T8886
Weight: 2 pounds 1 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Related part:
6T8886
PLATE-STRG-YM
3807517
CL
You can buy:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Clutch Disc 6T-8886 Fit Intended For Tractor D8K Pipelayer 583K
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts || Final Drives
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts || Final Drives
Clutch Disc 6T-8886 Fit Intended For Tractor D8K Pipelayer 583K
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts || Final Drives
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts || Final Drives
Information:
Remove Water Pump
1. Drain the cooling system. 2. Remove the water pump water inlet pipe (1).3. Remove the two elbow-to-pump retaining bolts (2).4. Remove the pump-to-timing gear plate mounting bolts and nuts (3).5. Remove the water pump - weight 60 lbs. (27 kg).Install Water Pump
1. Position the water pump on engine, and install mounting bolts and nuts.2. Install the two elbow-to-pump retaining bolts.3. Install the pump water inlet pipe.4. Fill the cooling system.Disassemble Water Pump
preparatory step: a) remove water pump 1. Remove the water pump drive gear. Remove the four adapter assembly-to-water pump retaining nuts (1). Remove the adapter assembly (2). 2. Remove the thrust washer from adapter assembly. Using tool setup (A), remove the bearing from adapter assembly. 3. Remove the impeller and housing assembly (3) from water pump housing assembly.4. Remove the impeller retaining nut, washer and cotter pin. Tap on the shaft with a soft hammer, and remove the impeller from shaft. Remove the spring and carbon face seal assembly.5. Bend the bearing assembly retaining locks. Remove the two retaining bolts, lock and retainers.6. Remove the shaft and bearing assembly from the impeller housing. Remove the O-ring seal from shaft.7. Bend the spanner nut retaining lock. Using spanner wrench (B), remove nut from shaft. 8. Press the shaft (4) out of the bearing (5).9. Remove the ceramic ring seal and rubber O-ring seal from impeller housing.10. Remove the lip-type seal from impeller housing.11. Remove the O-ring seals from impeller housing.Assemble Water Pump
1. Using tool setup (C), install lip-type seal in impeller housing with lip of seal toward the bearing assembly. Lubricate the lip of seal. 2. Press the bearing assembly on shaft. Install the spanner nut (1) and lock. Tighten nut with spanner wrench (B) to 65 10 lb. ft. (8,99 1,4 mkg) and bend lock.3. Position the shaft and bearing assembly in impeller housing, and install retaining bolts, lock and retainer. Bend the lock.4. Wet the rubber O-ring seal, ceramic ring seal, and bore of impeller housing with water. Install the rubber O-ring seal in housing. Using hand pressure only, install the ceramic ring seal inside of rubber seal with the polished surface toward the impeller. Make sure that ceramic ring seal and rubber seal are seated in housing.5. Wet the inside diameter of bellows on carbon seal assembly, and the shaft of pump with water. Using hand pressure only, press the carbon seal assembly on shaft until carbon surface contacts ceramic ring. Install the spring on shaft. 6. Position the impeller on shaft. Install retaining washer and nut (2). Tighten nut to 30 5 lb. ft. (4,15 0,7 mkg). Install the cotter pin (3) and bend both legs around nut.7. Install the O-ring seals on impeller housing. Lubricate the seals, and install impeller housing in water pump housing assembly.8. Using tool setup (A), install bearing in adapter housing.9. Position the adapter housing on water pump, and install the four retaining nuts. Check the impeller clearance (4). Clearance between impeller and water pump housing
1. Drain the cooling system. 2. Remove the water pump water inlet pipe (1).3. Remove the two elbow-to-pump retaining bolts (2).4. Remove the pump-to-timing gear plate mounting bolts and nuts (3).5. Remove the water pump - weight 60 lbs. (27 kg).Install Water Pump
1. Position the water pump on engine, and install mounting bolts and nuts.2. Install the two elbow-to-pump retaining bolts.3. Install the pump water inlet pipe.4. Fill the cooling system.Disassemble Water Pump
preparatory step: a) remove water pump 1. Remove the water pump drive gear. Remove the four adapter assembly-to-water pump retaining nuts (1). Remove the adapter assembly (2). 2. Remove the thrust washer from adapter assembly. Using tool setup (A), remove the bearing from adapter assembly. 3. Remove the impeller and housing assembly (3) from water pump housing assembly.4. Remove the impeller retaining nut, washer and cotter pin. Tap on the shaft with a soft hammer, and remove the impeller from shaft. Remove the spring and carbon face seal assembly.5. Bend the bearing assembly retaining locks. Remove the two retaining bolts, lock and retainers.6. Remove the shaft and bearing assembly from the impeller housing. Remove the O-ring seal from shaft.7. Bend the spanner nut retaining lock. Using spanner wrench (B), remove nut from shaft. 8. Press the shaft (4) out of the bearing (5).9. Remove the ceramic ring seal and rubber O-ring seal from impeller housing.10. Remove the lip-type seal from impeller housing.11. Remove the O-ring seals from impeller housing.Assemble Water Pump
1. Using tool setup (C), install lip-type seal in impeller housing with lip of seal toward the bearing assembly. Lubricate the lip of seal. 2. Press the bearing assembly on shaft. Install the spanner nut (1) and lock. Tighten nut with spanner wrench (B) to 65 10 lb. ft. (8,99 1,4 mkg) and bend lock.3. Position the shaft and bearing assembly in impeller housing, and install retaining bolts, lock and retainer. Bend the lock.4. Wet the rubber O-ring seal, ceramic ring seal, and bore of impeller housing with water. Install the rubber O-ring seal in housing. Using hand pressure only, install the ceramic ring seal inside of rubber seal with the polished surface toward the impeller. Make sure that ceramic ring seal and rubber seal are seated in housing.5. Wet the inside diameter of bellows on carbon seal assembly, and the shaft of pump with water. Using hand pressure only, press the carbon seal assembly on shaft until carbon surface contacts ceramic ring. Install the spring on shaft. 6. Position the impeller on shaft. Install retaining washer and nut (2). Tighten nut to 30 5 lb. ft. (4,15 0,7 mkg). Install the cotter pin (3) and bend both legs around nut.7. Install the O-ring seals on impeller housing. Lubricate the seals, and install impeller housing in water pump housing assembly.8. Using tool setup (A), install bearing in adapter housing.9. Position the adapter housing on water pump, and install the four retaining nuts. Check the impeller clearance (4). Clearance between impeller and water pump housing
Caterpillar parts catalog:
Parts disc Caterpillar catalog:
8M5070
DISC ASSEM.
594, 594H, D8H, D8K, D9G, D9H
594, 594H, D8H, D8K, D9G, D9H
5S7830
DISC ASSEM.
657B, 772, 777, D8H, D8K, D9G, D9H
657B, 772, 777, D8H, D8K, D9G, D9H
8P4736
DISC ASSEM.
594H, D8K, D9H
594H, D8K, D9H
1P6996
DISC ASSEM.
583K, D8K
583K, D8K
8F4453
DISC
583H, D8H, D8K, D9E
583H, D8H, D8K, D9E
6T8687
DISC-FRICTION
518, 916, 926, 931B, D4B, D4H, IT18B, IT28
518, 916, 926, 931B, D4B, D4H, IT18B, IT28
7T5726
DISC-FRICTION
D6H, D7H, D8N
D6H, D7H, D8N
2Y4654
DISC AS
D4E
D4E
3T6220
DISC-FRICTION
D3B, D5H
D3B, D5H
6T7180
DISC-FRICTION
D4H, D5H
D4H, D5H
6T8686
DISC-FRICTION
916, 926, D4B, D4H, IT18B, IT28
916, 926, D4B, D4H, IT18B, IT28
8P2036
DISC-THRUST
966D, 980C, D300B, D6H, D7H
966D, 980C, D300B, D6H, D7H
9P1861
DISC-FRICTION
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
7G3129
DISC-FRICTION
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
3T9874
DISC AS-FRICTION
518, 931B
518, 931B