7T3135 DISC-THRUST Caterpillar parts
926, D4H, D4HTSK II, D5C, IT28B
Rating:
Alternative (cross code) number:
CA7T3135
7T-3135
7T3135
CA7T3135
7T-3135
7T3135
Weight: 0.01 pounds 0 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compatible equipment models: 7T3135:
Number on catalog scheme:
52
For full view, you need register
Information:
Remove Oil Pump
start by: a) remove oil pan 1. Remove the suction elbow (2) for the scavenge section of the oil pump.2. Remove the suction screen mounting bolt (1).3. Remove the mounting bolts (3) and remove the oil pump. Weight 35 lbs. (16 kg).Install Oil Pump
1. Fill the oil pump with clean SAE 30 oil.2. Put the oil pump in position on the engine. Install the locks and fastening bolts.3. Install the suction screen fastening bolt.4. Install suction elbow for the scavenge section of the oil pump.end by: a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove the oil pump idler gear (1). Remove bearing (2) from idler gear, using tool group (A).2. Remove the suction bell assembly (3).3. Remove the nut, washer, and cotter pin from the oil pump drive shaft. Install the nut even with the end of the drive shaft. 4. Pull the pump drive gear from the shaft, using tool group (C). Remove the woodruff key from the shaft.5. Remove the end plate (4), spring, and plunger.6. Remove the oil pump body assembly (5). 7. Remove the oil pump gears (6).8. Remove the plate (7).9. Remove the two shaft and gear assemblies (8). 10. Remove the bearings from the two body assemblies, using tool group (B).Assemble Oil Pump
1. Install the bearings in the two body assemblies, using tool group (B). The inside edge of each bearing must be even with the inside surface of the pump body. 2. Put clean SAE 30 oil on the two shaft and gear assemblies (1), and install them in the oil pump body (3).3. Install the plate (2).4. Install a woodruff key in each oil pump shaft. 5. Put clean SAE 30 oil on the scavenge oil pump gears (5), and install them on the shafts.6. Install the oil pump body (4). 7. Install the plunger (7) and spring (6) in the body. Install the end plate.8. Install the woodruff key in the drive shaft, and put the drive gear in position on the shaft.9. Install the nut and washer on the shaft. Tighten the nut to 60 lb.ft. (8,3 mkg) plus the amount needed for cotter pin hole alignment. Install the cotter pin.10. Install the suction bell assembly. 11. Install the bearing in the oil pump idler gear, using tool group (A). Install the idler gear on the oil pump.end by: a) install oil pump
start by: a) remove oil pan 1. Remove the suction elbow (2) for the scavenge section of the oil pump.2. Remove the suction screen mounting bolt (1).3. Remove the mounting bolts (3) and remove the oil pump. Weight 35 lbs. (16 kg).Install Oil Pump
1. Fill the oil pump with clean SAE 30 oil.2. Put the oil pump in position on the engine. Install the locks and fastening bolts.3. Install the suction screen fastening bolt.4. Install suction elbow for the scavenge section of the oil pump.end by: a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove the oil pump idler gear (1). Remove bearing (2) from idler gear, using tool group (A).2. Remove the suction bell assembly (3).3. Remove the nut, washer, and cotter pin from the oil pump drive shaft. Install the nut even with the end of the drive shaft. 4. Pull the pump drive gear from the shaft, using tool group (C). Remove the woodruff key from the shaft.5. Remove the end plate (4), spring, and plunger.6. Remove the oil pump body assembly (5). 7. Remove the oil pump gears (6).8. Remove the plate (7).9. Remove the two shaft and gear assemblies (8). 10. Remove the bearings from the two body assemblies, using tool group (B).Assemble Oil Pump
1. Install the bearings in the two body assemblies, using tool group (B). The inside edge of each bearing must be even with the inside surface of the pump body. 2. Put clean SAE 30 oil on the two shaft and gear assemblies (1), and install them in the oil pump body (3).3. Install the plate (2).4. Install a woodruff key in each oil pump shaft. 5. Put clean SAE 30 oil on the scavenge oil pump gears (5), and install them on the shafts.6. Install the oil pump body (4). 7. Install the plunger (7) and spring (6) in the body. Install the end plate.8. Install the woodruff key in the drive shaft, and put the drive gear in position on the shaft.9. Install the nut and washer on the shaft. Tighten the nut to 60 lb.ft. (8,3 mkg) plus the amount needed for cotter pin hole alignment. Install the cotter pin.10. Install the suction bell assembly. 11. Install the bearing in the oil pump idler gear, using tool group (A). Install the idler gear on the oil pump.end by: a) install oil pump
Caterpillar parts catalog:
Parts disc Caterpillar catalog:
414E, 416, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436, 436C, 438C, 438D, ...
65, 65C, 65E, 735, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E, CX35, CX35-C18I, CX35-P800, D4H, D4HTSK II, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
517, 518, 527, 561M, 561N, 613C, 613C II, 613G, 931B, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, 966C, 966H, 966R, D5C, D5H, D5H XL, D5HTSK II, D5M, D5N...
D4H, D4H XL, D4HTSK II, D5H, D5H XL, D5HTSK II
D4H, D4H XL, D4HTSK II, D5H, D5H XL, D5HTSK II
528, 910, 916, 926, 931B, 931C, 931C II, 933, 939, D3C, D3C III, D4C, D4H, D5C, D5C III, D6D, IT18B, IT28B
5110B, 518, 527, 910, 916, 926, 931B, 931C, 931C II, 933, 939, D3C III, D4C, D4C III, D4H, D4HTSK II, D5C, D5C III, D5HTSK II, IT18B, IT28B
931B, 933, 939, D3C III, D4C III, D4E, D4E SR, D5C, D5C III
931B, 933, 939, 941, 951B, 955L, D3C III, D4C III, D4D, D4E, D4E SR, D5C, D5C III
931B, 933, 939, 951B, 955L, D3C III, D4C III, D4E, D5C, D5C III
939, D4C III, D4H, D4HTSK II, D5C, D5C III
916, 926, D4B, D4H, IT18B, IT28
966D, 980C, D300B, D6H, D7H
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
615, 814B, 815B, 966D, 980C, D250B, D25C, D25D, D300B, D6H, D7H
3T9874
DISC AS-FRICTION
518, 931B
518, 931B
24
6Y7913
DISC
518, 931B
518, 931B
955C, 977D
9W6045
DISC-THRUST
926, 931B, D3C, D4B, D4C, D4H, D4HTSK II, IT18B, IT28B
926, 931B, D3C, D4B, D4C, D4H, D4HTSK II, IT18B, IT28B