parts catalog

DISTRIBUTION AR 3966748 - Caterpillar

3966748 DISTRIBUTION AR Caterpillar parts 312D L DISTRIBUTION
Alternative (cross code) number:
Caterpillar 3966748 DISTRIBUTION AR

Buy DISTRIBUTION AR 3966748 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 3966748:

EXCAVATOR  312D L   Caterpillar
  For full view, you need register


Illustration 1 g01775574
Connections of the number 5 solenoid (third gear)This diagnostic code is associated with the third gear solenoid. The FMI 06 diagnostic code means that the ECM has determined that the current of the solenoid is above normal.The possible causes of this diagnostic code are listed below:
The solenoid energizer circuit of the modulating valve is shorted to ground.
The solenoid has failed.
The ECM has failed. This situation is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and that all connections are secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1405 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the starter keyswitch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the transmission harness.Expected Result:The CID 1405 FMI 06 diagnostic code changes to a CID 1405 FMI 05 diagnostic code when the solenoid is disconnected.Results:
YES - The CID 1405 FMI 06 diagnostic code changes to a CID 1405 FMI 05 diagnostic code when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - The CID 1405 FMI 06 diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZER CIRCUIT FOR A SHORT TO GROUND
Turn the starter keyswitch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the transmission harness.
Disconnect the connectors of the transmission harness from the ECM.
At the connector of the transmission harness, measure the resistance from the signal contact J2-8 (wire 902-BR) to all contacts that are used in the connectors for the transmission harness for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The transmission harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the transmission harness. The short is between J2-8 (wire 902-BR) and the circuit with the low resistance measurement.Repair: Repair the transmission harness or replace the transmission harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is

Caterpillar SIS machinery equipment:

Caterpillar SIS

Parts distribution Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.